SAM9X25 Atmel Corporation, SAM9X25 Datasheet - Page 809

• Manufacturer Part Number: SAM9X25
• Manufacturer: Atmel Corporation

Specifications of SAM9X25

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 7
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 2
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

11054A–ATARM–27-Jul-11
11054A–ATARM–27-Jul-11
mat is modified and includes sync information.
sists of a user-defined pattern that indicates the beginning of a valid data.
illustrates these patterns. If the start frame delimiter, also known as start bit, is one bit, (ONEBIT
to 1), a logic zero is Manchester encoded and indicates that a new character is being sent seri-
ally on the line. If the start frame delimiter is a synchronization pattern also referred to as sync
(ONEBIT to 0), a sequence of 3 bit times is sent serially on the line to indicate the start of a new
character. The sync waveform is in itself an invalid Manchester waveform as the transition
occurs at the middle of the second bit time. Two distinct sync patterns are used: the command
sync and the data sync. The command sync has a logic one level for one and a half bit times,
then a transition to logic zero for the second one and a half bit times. If the MODSYNC field in
the US_MR register is set to 1, the next character is a command. If it is set to 0, the next charac-
ter is a data. When direct memory access is used, the MODSYNC field can be immediately
updated with a modified character located in memory. To enable this mode, VAR_SYNC field in
US_MR register must be set to 1. In this case, the MODSYNC field in US_MR is bypassed and
the sync configuration is held in the TXSYNH in the US_THR register. The USART character for-
Figure 39-9. Preamble Patterns, Default Polarity Assumed
A start frame delimiter is to be configured using the ONEBIT field in the US_MR register. It con-
Manchester
Manchester
Manchester
Manchester
encoded
encoded
encoded
encoded
data
data
data
data
Txd
Txd
Txd
Txd
8 bit width "ZERO_ONE" Preamble
8 bit width "ONE_ZERO" Preamble
8 bit width "ALL_ZERO" Preamble
8 bit width "ALL_ONE" Preamble
SFD
SFD
SFD
SFD
SAM9X25
SAM9X25
Figure 39-10
DATA
DATA
DATA
DATA
809
809