SAM9X25 Atmel Corporation, SAM9X25 Datasheet - Page 530

• Manufacturer Part Number: SAM9X25
• Manufacturer: Atmel Corporation

Specifications of SAM9X25

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 7
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 2
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 32-3. UHP Clock Trees
530
530
SAM9X25
SAM9X25
MCK
AHB
For OHCI Full-speed operations only, the user has to perform the following:
• Enable UHP peripheral clock, bit (1 << AT91C_ID_UHPHS) in PMC_PCER register.
• Write CKGR_PLLCOUNT field in PMC_UCKR register.
• Enable UPLL, bit AT91C_CKGR_UPLLEN in PMC_UCKR register.
• Wait until UTMI_PLL is locked. LOCKU bit in PMC_SR register
• Enable BIAS, bit AT91C_CKGR_BIASEN in PMC_UCKR register.
• Select UPLLCK as Input clock of OHCI part, USBS bit in PMC_USB register.
• Program the OHCI clocks (UHP48M and UHP12M) with USBDIV field in PMC_USB register.
• Enable OHCI clocks, UHP bit in PMC_SCER register.
• Enable UHP peripheral clock, bit (1 << AT91C_ID_UHPHS) in PMC_PCER register.
• Select PLLACK as Input clock of OHCI part, USBS bit in PMC_USB register.
• Program the OHCI clocks (UHP48M and UHP12M) with USBDIV field in PMC_USB register.
• Enable the OHCI clocks, UHP bit in PMC_SCER register.
USBDIV must be 9 (division by 10) if UPLLCK is selected.
USBDIV value is to calculated regarding the PLLACK value and USB Full-speed accuracy.
Interface
Interface
Interface
Interface
Master
Master
EHCI
OHCI
OHCI
EHCI
User
User
Host Controller
Host Controller
USB 1.1 OHCI
USB 2.0 EHCI
OHCI clocks
Root Hub
Host SIE
Router
and
Port
30 MHz
30 MHz
UTMI transceiver
UTMI transceiver
UPLL (480 MHz)
FS transceiver
11054A–ATARM–27-Jul-11
11054A–ATARM–27-Jul-11