SAM9X25 Atmel Corporation, SAM9X25 Datasheet - Page 911

• Manufacturer Part Number: SAM9X25
• Manufacturer: Atmel Corporation

Specifications of SAM9X25

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 7
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 2
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

41.7.3
11054A–ATARM–27-Jul-11
11054A–ATARM–27-Jul-11
Time Management Unit
The CAN Controller integrates a free-running 16-bit internal timer. The counter is driven by the
bit clock of the CAN bus line. It is enabled when the CAN controller is enabled (CANEN set in the
CAN_MR register). It is automatically cleared in the following cases:
The application can also reset the internal timer by setting TIMRST in the CAN_TCR register.
The current value of the internal timer is always accessible by reading the CAN_TIM register.
When the timer rolls-over from FFFFh to 0000h, TOVF (Timer Overflow) signal in the CAN_SR
register is set. TOVF bit in the CAN_SR register is cleared by reading the CAN_SR register.
Depending on the corresponding interrupt mask in the CAN_IMR register, an interrupt is gener-
ated while TOVF is set.
In a CAN network, some CAN devices may have a larger counter. In this case, the application
can also decide to freeze the internal counter when the timer reaches FFFFh and to wait for a
restart condition from another device. This feature is enabled by setting TIMFRZ in the CAN_MR
register. The CAN_TIM register is frozen to the FFFFh value. A clear condition described above
restarts the timer. A timer overflow (TOVF) interrupt is triggered.
To monitor the CAN bus activity, the CAN_TIM register is copied to the CAN _TIMESTP register
after each start of frame or end of frame and a TSTP interrupt is triggered. If TEOF bit in the
CAN_MR register is set, the value is captured at each End Of Frame, else it is captured at each
Start Of Frame. Depending on the corresponding mask in the CAN_IMR register, an interrupt is
generated while TSTP is set in the CAN_SR. TSTP bit is cleared by reading the CAN_SR
register.
The time management unit can operate in one of the two following modes:
Timestamping Mode is enabled by clearing TTM field in the CAN_MR register. Time Triggered
Mode is enabled by setting TTM field in the CAN_MR register.
• after a reset
• when the CAN controller is in Low-power Mode is enabled (LPM bit set in the CAN_MR and
• after a reset of the CAN controller (CANEN bit in the CAN_MR register)
• in Time-triggered Mode, when a message is accepted by the last mailbox (rising edge of the
• Timestamping mode: The value of the internal timer is captured at each Start Of Frame or
• Time Triggered mode: A mailbox transfer operation is triggered when the internal timer
SLEEP bit set in the CAN_SR)
MRDY signal in the CAN_MSR
each End Of Frame
reaches the mailbox trigger.
last_mailbox_number
register).
SAM9X25
SAM9X25
911
911