SAM9X25 Atmel Corporation, SAM9X25 Datasheet - Page 913

• Manufacturer Part Number: SAM9X25
• Manufacturer: Atmel Corporation

Specifications of SAM9X25

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 7
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 2
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 41-5. CAN Bit Timing
11054A–ATARM–27-Jul-11
11054A–ATARM–27-Jul-11
CAN Clock
MCK
SYNC_
t
CSC
SEG
The SAMPLE POINT is the point in time at which the bus level is read and interpreted as the
value of that respective bit. Its location is at the end of PHASE_SEG1.
The ReSynchronization Jump Width defines the limit to the amount of lengthening or shortening
of the Phase Segments.
SJW is programmable to be the minimum of PHASE SEG1 and 4 TQ.
If the SMP field in the CAN_BR register is set, then the incoming bit stream is sampled three
times with a period of half a CAN clock period, centered on sample point.
In the CAN controller, the length of a bit on the CAN bus is determined by the parameters (BRP,
PROPAG, PHASE1 and PHASE2).
The time quantum is calculated as follows:
Note: The BRP field must be within the range [1, 0x7F], i.e., BRP = 0 is not authorized.
To compensate for phase shifts between clock oscillators of different controllers on the bus, the
CAN controller must resynchronize on any relevant signal edge of the current transmission. The
resynchronization shortens or lengthens the bit time so that the position of the sample point is
shifted with regard to the detected edge. The resynchronization jump width (SJW) defines the
maximum of time by which a bit period may be shortened or lengthened by resynchronization.
PROP_SEG
• SAMPLE POINT:
• SJW: ReSynchronization Jump Width.
t
PRS
t
t
BIT
CSC
t
t
t
PRS
PHS2
PHS1
t
SJW
=
=
=
t
CSC
=
=
=
BRP
t
CSC
NOMINAL BIT TIME
t
t
t
CSC
CSC
CSC
PHASE_SEG1
+
t
+
PRS
t
1
PHS1
PROPAG
PHASE2
SJW
PHASE1
+
t
MCK
PHS1
+
1
+
+
+
+
t
1
PHS2
1
1
Sample Point
PHASE_SEG2
t
PHS2
SAM9X25
SAM9X25
Transmission Point
913
913