AT32UC3L0256 Atmel Corporation, AT32UC3L0256 Datasheet - Page 759

• Manufacturer Part Number: AT32UC3L0256
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L0256

• Flash (kbytes): 256 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

31.5.2
31.5.2.1
31.5.2.2
32145A–12/2011
Public JTAG Instructions
IDCODE
SAMPLE_PRELOAD
Table 31-11. Instruction Description (Continued)
The JTAG standard defines a number of public JTAG instructions. These instructions are
described in the sections below.
This instruction selects the 32 bit Device Identification register (DID) as Data Register. The DID
register consists of a version number, a device number, and the manufacturer code chosen by
JEDEC. This is the default instruction after a JTAG reset. Details about the DID register can be
found in the module configuration section at the end of this chapter.
Starting in Run-Test/Idle, the Device Identification register is accessed in the following way:
Table 31-12. IDCODE Details
This instruction takes a snap-shot of the input/output pins without affecting the system operation,
and pre-loading the scan chain without updating the DR-latch. The boundary-scan chain is
selected as Data Register.
Starting in Run-Test/Idle, the Device Identification register is accessed in the following way:
Instruction
DR Size
DR input value
DR output value
Instructions
IR input value
IR output value
DR Size
DR input value
DR output value
1. Select the IR Scan path.
2. In Capture-IR: The IR output value is latched into the shift register.
3. In Shift-IR: The instruction register is shifted by the TCK input.
4. Return to Run-Test/Idle.
5. Select the DR Scan path.
6. In Capture-DR: The IDCODE value is latched into the shift register.
7. In Shift-DR: The IDCODE scan chain is shifted by the TCK input.
8. Return to Run-Test/Idle.
Description
Shows the number of bits in the data register chain when this instruction is active.
Example: 34 bits
Shows which bit pattern to shift into the data register in the Shift-DR state when this
instruction is active. Multiple such lines may exist, e.g., to distinguish between
reads and writes.
Example: aaaaaaar xxxxxxxx xxxxxxxx xxxxxxxx xx
Shows the bit pattern shifted out of the data register in the Shift-DR state when this
instruction is active. Multiple such lines may exist, e.g., to distinguish between
reads and writes.
Example: xx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxeb
Details
00001 (0x01)
p0001
32
xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx
Device Identification Register
AT32UC3L0128/256
759