AT32UC3L0256 Atmel Corporation, AT32UC3L0256 Datasheet - Page 442

• Manufacturer Part Number: AT32UC3L0256
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L0256

• Flash (kbytes): 256 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

20.8.1
Name:
Access Type:
Offset:
Reset Value:
• LASTXFER: Last Transfer
• FLUSHFIFO: Flush Fifo Command
• SWRST: SPI Software Reset
• SPIDIS: SPI Disable
• SPIEN: SPI Enable
32145A–12/2011
SWRST
31
23
15
7
-
-
-
1: The current NPCS will be deasserted after the character written in TD has been transferred. When CSRn.CSAAT is one, this
allows to close the communication with the current serial peripheral by raising the corresponding NPCS line as soon as TD
transfer has completed.
0: Writing a zero to this bit has no effect.
1: If The FIFO Mode is enabled (MR.FIFOEN written to one) and if an overrun error has been detected, this command allows to
empty the FIFO.
0: Writing a zero to this bit has no effect.
1: Writing a one to this bit will reset the SPI. A software-triggered hardware reset of the SPI interface is performed. The SPI is in
slave mode after software reset. Peripheral DMA Controller channels are not affected by software reset.
0: Writing a zero to this bit has no effect.
1: Writing a one to this bit will disable the SPI. As soon as SPIDIS is written to one, the SPI finishes its transfer, all pins are set
in input mode and no data is received or transmitted. If a transfer is in progress, the transfer is finished before the SPI is
disabled. If both SPIEN and SPIDIS are equal to one when the CR register is written, the SPI is disabled.
0: Writing a zero to this bit has no effect.
1: Writing a one to this bit will enable the SPI to transfer and receive data.
0: Writing a zero to this bit has no effect.
Control Register
30
22
14
6
-
-
-
-
CR
Write-only
0x00
0x00000000
29
21
13
5
-
-
-
-
28
20
12
4
-
-
-
-
27
19
11
3
-
-
-
-
26
18
10
2
-
-
-
-
AT32UC3L0128/256
SPIDIS
25
17
9
1
-
-
-
FLUSHFIFO
LASTXFER
SPIEN
24
16
8
0
-
442