AT32UC3L0256 Atmel Corporation, AT32UC3L0256 Datasheet - Page 455

• Manufacturer Part Number: AT32UC3L0256
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L0256

• Flash (kbytes): 256 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• BITS: Bits Per Transfer
• CSAAT: Chip Select Active After Transfer
• CSNAAT: Chip Select Not Active After Transfer (Ignored if CSAAT = 1)
• NCPHA: Clock Phase
• CPOL: Clock Polarity
32145A–12/2011
DLYBCS
-------------------------------- -
The BITS field determines the number of data bits transferred. Reserved values should not be used.
1: The Peripheral Chip Select does not rise after the last transfer is achieved. It remains active until a new transfer is requested
on a different chip select.
0: The Peripheral Chip Select Line rises as soon as the last transfer is achieved.
0: The Peripheral Chip Select does not rise between two transfers if the TDR is reloaded before the end of the first transfer and
if the two transfers occur on the same Chip Select.
1: The Peripheral Chip Select rises systematically between each transfer performed on the same slave for a minimal duration of:
1: Data is captured after the leading (inactive-to-active) edge of SPCK and changed on the trailing (active-to-inactive) edge of
SPCK.
0: Data is changed on the leading (inactive-to-active) edge of SPCK and captured after the trailing (active-to-inactive) edge of
SPCK.
NCPHA determines which edge of SPCK causes data to change and which edge causes data to be captured. NCPHA is used
with CPOL to produce the required clock/data relationship between master and slave devices.
1: The inactive state value of SPCK is logic level one.
0: The inactive state value of SPCK is logic level zero.
DLYBCS
---------------------- -
CLKSPI
CLKSPI
+
(if DLYBCT field is different from 0)
BITS
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
1
(if DLYBCT field equals 0)
Bits Per Transfer
Reserved
Reserved
Reserved
10
11
12
13
14
15
16
8
9
4
5
6
7
AT32UC3L0128/256
455