AT32UC3L0256 Atmel Corporation, AT32UC3L0256 Datasheet - Page 379

• Manufacturer Part Number: AT32UC3L0256
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L0256

• Flash (kbytes): 256 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.6
19.6.1
Figure 19-2. Baud Rate Generator
19.6.1.1
19.6.1.2
32145A–12/2011
Functional Description
Baud Rate Generator
CLK_USART/DIV
CLK
CLK_USART
Baud Rate in Asynchronous Mode
Baud Rate Calculation Example
Reserved
USCLKS
The baud rate generator provides the bit period clock named the Baud Rate Clock to both
receiver and transmitter. It is based on a 16-bit divider, which is specified in the Clock Divider
field in the Baud Rate Generator Register (BRGR.CD). A non-zero value enables the generator,
and if CD is one, the divider is bypassed and inactive. The Clock Selection field in the Mode
Register (MR.USCLKS) selects clock source between:
If the external CLK clock is selected, the duration of the low and high levels of the signal pro-
vided on the CLK pin must be at least 4.5 times longer than those provided by CLK_USART.
If the USART is configured to operate in an asynchronous mode, the selected clock is divided by
the CD value before it is provided to the receiver as a sampling clock. Depending on the Over-
sampling Mode bit (MR.OVER) value, the clock is then divided by either 8 (OVER=1), or 16
(OVER=0). The baud rate is calculated with the following formula:
This gives a maximum baud rate of CLK_USART divided by 8, assuming that CLK_USART is
the fastest clock possible, and that OVER is one.
Table 19-3
clock frequencies. This table also shows the actual resulting baud rate and error.
0
1
3
2
• CLK_USART (internal clock)
• CLK_USART/DIV (a divided CLK_USART, refer to Module Configuration section)
• CLK (external clock, available on the CLK pin)
BaudRate
shows calculations based on the CD field to obtain 38400 baud from different source
16-bit Counter
=
CD
----------------------------------------------- -
8 2 OVER
SelectedClock
–
USCLKS= 3
0
SYNC
CD
CD
>1
0
1
0
1
OVER
Sampling
Divider
AT32UC3L0128/256
FIDI
0
1
SYNC
CLK
BaudRate
Sampling
Clock
Clock
379