AT32UC3L0256 Atmel Corporation, AT32UC3L0256 Datasheet - Page 615

• Manufacturer Part Number: AT32UC3L0256
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L0256

• Flash (kbytes): 256 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

26.7.4
26.7.5
32145A–12/2011
Resistive Touch Screen Sequencer
Pen Detect
The Resistive Touch Screen Sequencer is responsible for applying voltage to the resistive touch
screen films as described in
output value of the ADP and AD pins. This allows the Resistive Touch Screen Sequencer to add
a voltage gradient on one film while keeping the other film floating so a touch can be measured.
The Resistive Touch Screen Sequencer will when measuring the vertical position, apply VDD
and GND to the pins connected to X
measurement of Y
non ideal pad drivers, the actual voltage of X
VDD and GND can be used in the contact point calculation to increase accuracy. See second
formula in
When the vertical values are converted the same setup is applies for the second axes, by setting
X
details.
If no contact is applied to the resistive touch screen films, any resistive touch screen conversion
result will be undefined as the film being measured is floating. This can be avoided by enabling
Pen Detect and only trigger resistive touch screen conversions when the Pen Contact
(PENCNT) status bit in the Status Register (SR) is one. Pen Detect is enabled by writing a one
to the Pen Detect (PENDET) bit in the Mode Register (MR).
When Pen Detect is enabled, the ADCIFB grounds the vertical panel by applying GND to X
X
will in this mode be tristated. Since there is no contact, no current is flowing and there is no
related power consumption. As soon as a contact occurs, GND will propagate to Y
down Y
A programmable debouncing filter can be used to filter out false pen detects because of noise.
The debouncing filter is programmable from one CLK_ADC period and up to 2
ods. The debouncer length is set by writing to the PENDBC field in MR.
P
M
and X
and polarizes the horizontal panel by enabling pull-up on the pin connected to Y
P
, allowing the contact to be registered by the ADCIFB.
M
Section
in tristate mode and applying VDD and GND to Y
P
26.7.2.
can proceed without interference. To compensate for ADC offset errors and
Section
P
26.7.2. This is done by controlling the output enable and the
and X
M
P
. The Y
and X
P
M
and Y
is measured as well, so the real values for
AT32UC3L0128/256
M
P
and Y
pins are put in tristate mode so the
M
. Refer to
15
Section 26.8.3
CLK_ADC peri-
P
. The Y
M
by pulling
P
M
and
615
pin
for