UPSD3433EB40U6 STMicroelectronics, UPSD3433EB40U6 Datasheet - Page 60

• Manufacturer Part Number: UPSD3433EB40U6
• Description: MCU 8BIT 8032 128KB FLASH 80TQFP
• Manufacturer: STMicroelectronics
• Series: µPSDr

Specifications of UPSD3433EB40U6

• Core Processor: 8032
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 46
• Program Memory Size: 160KB (160K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• For Use With: 497-5518 - EVAL BOARD RFID READER497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 497-5660

MCU clock generation
14.2.2
60/293
USB_CLK
The uPSD34xx has a dedicated analog phase locked loop (PLL) that can be configured to
generate the 48MHz USB_CLK clock on a wide range of f
must be at 48MHz for the USB to function properly.
The PLL is enabled after power up. The power on lock time for the PLL clock is about 200µs,
and the firmware should wait that much time before enabling the USB_CLK by setting the
UPLLCE Bit in the CCON0 Register to '1.' The PLL is disabled in Power-down mode, it can
also be disabled or enabled by writing to the PLLEN Bit in the CCON0 Register.
The PLL output clock frequency (f
formula:
where PLLM and PLLD are the multiplier and divisor that are specified in the CCON1
Register. The f
generate a stable USB_CLK:
The USB requires a 48MHz clock to operate correctly. The PLLM[4:0] and PLLD[3:0] values
must be selected so as to generate a USB_CLK that is as close to 48MHz as possible at
different oscillator frequencies (f
can be used on common f
Table 21.
a)
b)
c)
(MHz)
f
40.0
36.0
33.0
30.0
24.0
16.0
12.0
OSC
8.0
6.0
3.0
–1 ≤ PLLM ≤ 30 (binary: [11111] ≤ PLLM[4:0] ≤ [11110]),
–1 ≤ PLLD ≤ 14 (binary: [1111] ≤ PLLD[3:0] ≤ [1110]), and
f
OSC
PLLM and PLLD Values for Different f
/(PLLD+2) must be equal to or greater than 3MHz.
OSC
, the PLLM and PLLD range must meet the following conditions to
decimal
22
30
30
22
30
14
18
28
30
6
PLLM[4:0]
OSC
f
USBCLK
frequencies.
OSC
USB_CLK
binary
10110
00110
11110
01110
10010
11100
11110
10110
11110
11110
).
=
Table 21
[
[
f
(
OSC
PLLD
) can be determined by using the following
×
(
+
PLLM
lists some of the PLLM and PLLD values that
2
)
×
decimal
2
+
–1
]
8
1
9
3
3
3
2
0
0
OSC
2
)
]
PLLD[3:0]
⁄
Frequencies
OSC
frequencies. The USB_CLK
binary
1000
0001
1001
0011
0011
0011
0010
0000
0000
1111
f
USB_CLK
uPSD34xx
(MHz)
48.0
48.0
48.0
48.0
48.0
48.0
48.0
48.0
48.0
48.0