DF70845AD80FPV Renesas Electronics America, DF70845AD80FPV Datasheet - Page 139

• Manufacturer Part Number: DF70845AD80FPV
• Description: IC SUPERH MCU FLASH 112LQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7080r

Specifications of DF70845AD80FPV

• Core Size: 32-Bit
• Program Memory Size: 512KB (512K x 8)
• Core Processor: SH-2
• Speed: 80MHz
• Connectivity: EBI/EMI, FIFO, I²C, SCI, SSU
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• No. Of I/o's: 76
• Ram Memory Size: 32KB
• Cpu Speed: 80MHz
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 3V To 3.6V, 4.5V To 5.5V
• Embedded Interface Type: I2C, SCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K570865S001BE - KIT STARTER FOR SH7086R0K570865S000BE - KIT STARTER FOR SH7086HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

4.5
Selecting division ratios for the frequency divider can change the frequencies of the internal clock
(Iφ), bus clock (Bφ), peripheral clock (Pφ), MTU2S clock (MIφ), and MTU2 clock (MPφ). This is
controlled by software through the frequency control register (FRQCR). The following describes
how to specify the frequencies.
1. In the initial state, IFC2 to IFC0 = H'011 (×1/4), BFC2 to BFC0 = H'011 (×1/4), PFC2 to
2. Stop all modules except the CPU, on-chip ROM, and on-chip RAM.
3. Set the desired values in bits IFC2 to IFC0, BFC2 to BFC0, PFC2 to PFC0, MIFC2 to MIFC0,
4. After an instruction to rewrite FRQCR has been issued, the actual clock frequencies will
Note: (1 to 24n) depends on the internal state.
PFC0 = H'011 (×1/4), MIFC2 to MIFC0 = H'011 (×1/4), and MPFC2 to MPFC0 = H'011
(×1/4).
and MPFC2 to MPFC0 bits. Since the frequency multiplication ratio in the PLL circuit is fixed
at ×8, the frequencies are determined only be selecting division ratios. When specifying the
frequencies, satisfy the following condition: internal clock (Iφ) ≥ bus clock (Bφ) ≥ peripheral
clock (Pφ). When using the MTU2S clock and MTU2 clock, specify the frequencies to satisfy
the following condition: internal clock (Iφ) ≥ MTU2S clock (MIφ) ≥ MTU2 clock (MPφ) ≥
peripheral clock (Pφ) and bus clock (Bφ) ≥ MTU2 clock (MPφ).
Code to rewrite values of FRQCR should be executed in the on-chip ROM or on-chip RAM.
change after (1 to 24n) cyc + 11Bφ + 7Pφ.
n: Division ratio specified by the BFC bit in FRQCR (1, 1/2, 1/3, 1/4, or 1/8)
cyc: Clock obtained by dividing EXTAL by 8 with the PLL.
Changing Frequency
Rev. 3.00 May 17, 2007 Page 81 of 1582
Section 4 Clock Pulse Generator (CPG)
REJ09B0181-0300