st72324bk STMicroelectronics, st72324bk Datasheet - Page 76
st72324bk
Manufacturer Part Number
st72324bk
Description
3 V/5 V Range 8-bit Mcu With 4/8 Kbyte Rom, 10-bit Adc, Four Timers And Spi
Manufacturer
STMicroelectronics
Datasheet
1.ST72324BK.pdf
(167 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
st72324bk6TA
Manufacturer:
FREESCALE
Quantity:
201
- Current page: 76 of 167
- Download datasheet (3Mb)
On-chip peripherals
76/167
One-pulse mode
One Pulse mode enables the generation of a pulse when an external event occurs. This
mode is selected via the OPM bit in the CR2 register.
The one pulse mode uses the Input Capture1 function and the Output Compare1 function.
Procedure to use one-pulse mode:
1.
2.
3.
Figure 40. One-pulse mode cycle
Then, on a valid event on the ICAP1 pin, the counter is initialized to FFFCh and OLVL2 bit is
loaded on the OCMP1 pin, the ICF1 bit is set and the value FFFDh is loaded in the IC1R
register.
Because the ICF1 bit is set when an active edge occurs, an interrupt can be generated if the
ICIE bit is set.
Clearing the Input Capture interrupt request (i.e. clearing the ICFi bit) is done in two steps:
1.
2.
The OC1R register value required for a specific timing application can be calculated using
the following formula:
Load the OC1R register with the value corresponding to the length of the pulse (see the
formula in the opposite column).
Select the following in the CR1 register:
–
–
–
Select the following in the CR2 register:
–
–
–
Reading the SR register while the ICFi bit is set.
An access (read or write) to the ICiLR register.
Using the OLVL1 bit, select the level to be applied to the OCMP1 pin after the
pulse.
Using the OLVL2 bit, select the level to be applied to the OCMP1 pin during the
pulse.
Select the edge of the active transition on the ICAP1 pin with the IEDG1 bit (the
ICAP1 pin must be configured as floating input).
Set the OC1E bit, the OCMP1 pin is then dedicated to the Output Compare 1
function.
Set the OPM bit.
Select the timer clock CC[1:0] (see
event occurs
on ICAP1
Counter
= OC1R
When
When
OCiR Value =
One pulse mode cycle
Table
PRESC
t
OCMP1 = OLVL2
OCMP1 = OLVL1
Counter is reset
*
ICR1 = Counter
ICF1 bit is set
f
CPU
42).
to FFFCh
- 5
ST72323 ST72323L
Related parts for st72324bk
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Low Cost, Real Time Emulator Series for ST7
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
Full-featured, real time emulator series for ST7
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
In-Circuit Programmer
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet: