AM79C970A Advanced Micro Devices, AM79C970A Datasheet - Page 89
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
AM79C970A
Manufacturer Part Number
AM79C970A
Description
PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C970A.pdf
(219 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AM79C970ACK
Manufacturer:
AMD
Quantity:
271
Company:
Part Number:
AM79C970AKC
Manufacturer:
AMtek
Quantity:
11
Part Number:
AM79C970AKC
Manufacturer:
AMD
Quantity:
20 000
Company:
Part Number:
AM79C970AKC/W
Manufacturer:
AMD
Quantity:
226
Part Number:
AM79C970AKC/W
Manufacturer:
AMD
Quantity:
20 000
Company:
Part Number:
AM79C970AKCW
Manufacturer:
AMD
Quantity:
6 557
Part Number:
AM79C970AVC
Manufacturer:
AMD
Quantity:
20 000
Note that the XTAL1 input must always be driven with a
clock source, even if GPSI mode is to be used. It is not
necessary for the XTAL1 clock to meet the normal fre-
quency and stability requirements in this case. Any fre-
quency between 8 MHz and 20 MHz is acceptable.
However, voltage drive requirements do not change.
When GPSI mode is used, XTAL1 must be driven for
several reasons:
Note that if a clock slower than 20 MHz is provided at the
XTAL1 input, the time needed for EEPROM read and
the internal S_RESET will increase.
External Address Detection Interface
The External Address Detection Interface (EADI) is pro-
vided to allow external address filtering. It is selected by
setting the EADISEL bit in BCR2 to ONE. This feature is
typically utilized for terminal servers, bridges and/or
router products. The EADI interface can be used in con-
junction with external logic to capture the packet desti-
nation address from the serial bit stream as it arrives at
the PCnet-PCI II controller, compare the captured ad-
dress with a table of stored addresses or identifiers, and
then determine whether or not the PCnet-PCI II control-
ler should accept the packet.
The EADI interface outputs are delivered directly from
the NRZ decoded data and clock recovered by the
Manchester decoder or input into the GPSI port. This al-
lows the external address detection to be performed in
parallel with frame reception and address comparison in
the MAC Station Address Detection (SAD) block of the
PCnet-PCI II controller.
Collision
Receive Clock
Receive Data
Receive Enable
Transmit Clock
Transmit Data
Transmit Enable
GPSI Function
The default H_RESET configuration for the PCnet-
PCI II controller is AUI port selected and until GPSI
mode is selected, the XTAL1 clock is needed for
some internal operations (namely, RESET).
The XTAL1 clock drives the EEPROM read opera-
tion, regardless of the network mode selected.
The XTAL1 clock determines the length the internal
S_RESET caused by the read of the Reset register,
regardless of the network mode.
GPSI I/O Type
O
O
I
I
I
I
I
Table 10. GPSI Pin Configuration
C-LANCE
P R E L I M I N A R Y
GPSI Pin
RENA
CLSN
RCLK
TENA
TCLK
RX
TX
Am79C970A
SRDCLK is provided to allow clocking of the receive bit
stream into the external address detection logic. Note
that when the 10BASE-T port is selected, transitions on
SRDCLK will only occur during receive activity. When
the AUI or GPSI port is selected, transitions on SRDCLK
will occur during both transmit and receive activity. Once
a received frame commences and data and clock are
available from the decoder, the EADI logic will monitor
the alternating (1,0) preamble pattern until the two
ONEs of the Start Frame Delimiter (SFD, 10101011 bit
pattern) are detected, at which point the SFBD output
will be driven HIGH.
The SFBD signal will initially be LOW. The assertion of
SFBD is a signal to the external address detection logic
that the SFD has been detected and that subsequent
SRDCLK cycles will deliver packet data to the external
logic. Therefore, when SFBD is asserted, the external
address matching logic should begin de-serialization of
the SRD data and send the resulting destination ad-
dress to a Content Addressable Memory (CAM) or other
address detection device. In order to reduce the amount
of logic external to the PCnet-PCI II controller for multi-
ple address decoding systems, the SFBD signal will
toggle at each new byte boundary within the packet,
subsequent to the SFD. This eliminates the need for ex-
ternally supplying byte framing logic.
SRD is the decoded NRZ data from the network. This
signal can be used for external address detection. Note
that when the 10BASE-T port is selected, transitions on
SRD will only occur during receive activity. When the
AUI or GPSI port is selected, transitions on SRD will oc-
cur during both transmit and receive activity.
The EAR pin should be driven LOW by the external ad-
dress comparison logic to reject a frame.
If an address match is detected by comparison with
either the Physical Address or Logical Address Filter
registers contained within the PCnet-PCI II controller or
the frame is of the type “Broadcast”, then the frame will
be accepted regardless of the condition of EAR. When
PCnet-PCI II
Controller
GPSI Pin
RXDAT
RXCLK
TXCLK
TXDAT
CLSN
RXEN
TXEN
PCnet-PCI II
Pin Number
Controller
81
85
86
83
80
75
77
PCnet-PCI II
Expansion
Controller
ROM Pin
ERD3
ERD1
ERD0
ERD2
ERD4
ERD7
ERD6
AMD
89