ATxmega32D4 Atmel Corporation, ATxmega32D4 Datasheet - Page 222
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATxmega32D4
Manufacturer Part Number
ATxmega32D4
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega32D4
Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
34
Ext Interrupts
34
Usb Speed
No
Usb Interface
No
Spi
4
Twi (i2c)
2
Uart
2
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
12
Adc Resolution (bits)
12
Adc Speed (ksps)
200
Analog Comparators
2
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
14
Input Capture Channels
14
Pwm Channels
14
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATxmega32D4-AU
Manufacturer:
Atmel
Quantity:
123
Part Number:
ATxmega32D4-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATxmega32D4-CU
Manufacturer:
Maxim
Quantity:
71
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 910
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 704
Part Number:
ATxmega32D4-MH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
19.3
19.3.1
19.3.2
19.3.3
8210B–AVR–04/10
Registers Description
TXPLCTRL - IRCOM Transmitter Pulse Length Control Register
RXPLCTRL - IRCOM Receiver Pulse Length Control Register
CTRL - IRCOM Control Register
• Bits 7:0 - TXPLCTRL[7:0] - Transmitter Pulse Length Control
The 8-bit value sets the pulse modulation scheme for the transmitter. Setting this register will
have no effect if IRCOM mode is not selected by a USART.
By leaving this register value to zero, 3/16 of baud rate period pulse modulation is used.
Setting this value from 1 to 254 will give a fixed pulse length coding. The 8-bit value sets the
number of system clock periods for the pulse. The start of the pulse will be synchronized with the
rising edge of the baud rate clock.
Setting the value to 255 (0xFF) will disable pulse coding, letting the RX and TX signals pass
through the IRCOM Module unaltered. This enables other features through the IRCOM Module,
such as half-duplex USART, Loop-back testing and USART RX input from an Event Channel.
Note:
• Bits 7:0 - RXPLCTRL[7:0] - Receiver Pulse Length Control
The 8-bit value sets the filter coefficient for the IRCOM transceiver. Setting this register will have
no effect if IRCOM mode is not selected by a USART.
By leaving this register value to zero, filtering is disabled. Setting this value between 1 and 255
will enable filtering, where x+1 equal samples is required for the pulse to be accepted.
Note:
• Bits 7:4 - Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
Bit
+0x00
Read/Write
Initial Value
Bit
+0x00
Read/Write
Initial Value
Bit
+0x00
Read/Write
Initial Value
TXPCTRL must be configured before USART transmitter is enabled (TXEN).
RXPCTRL must be configured before USART receiver is enabled (RXEN).
R/W
R/W
7
0
7
0
7
–
R
0
R/W
R/W
6
0
6
0
6
–
R
0
R/W
R/W
5
0
5
0
R
5
–
0
R/W
R/W
4
0
TXPLCTRL[7:0]
4
0
RXPLCTRL[7:0]
R
4
–
0
R/W
R/W
R/W
3
0
3
0
3
0
R/W
R/W
R/W
2
0
2
0
2
0
EVSEL[3:0]
R/W
R/W
R/W
1
0
1
0
1
0
XMEGA D
R/W
R/W
R/W
0
0
0
0
0
0
TXPLCTRL
RXPLCTRL
CTRL
222