ATxmega32D4 Atmel Corporation, ATxmega32D4 Datasheet - Page 213

• Manufacturer Part Number: ATxmega32D4
• Manufacturer: Atmel Corporation

Specifications of ATxmega32D4

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 4
• Twi (i2c): 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 200
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 14
• Input Capture Channels: 14
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

18.13 IRCOM Mode of Operation
18.14 Register Description
18.14.1
18.14.2
8210B–AVR–04/10
DATA - USART I/O Data Register
STATUS - USART Status Register
IRCOM mode can be enabled to use the IRCOM Module with the USART. This enables IrDA 1.4
physical compliant modulation and demodulation for baud rates up to 115.2 Kbps. When IRCOM
mode is enabled, Double Transmission Speed cannot be used for the USART.
For devices with more than one USART, IRCOM mode can only be enabled for one USART at a
time. For details refer to
The USART Transmit Data Buffer Register and USART Receive Data Buffer Registers share the
same I/O address referred to as USART Data Register (DATA). The Transmit Data Buffer Reg-
ister (TXB) will be the destination for data written to the DATA Register location. Reading the
DATA Register location will return the contents of the Receive Data Buffer Register (RXB).
For 5-, 6-, or 7-bit characters the upper unused bits will be ignored by the Transmitter and set to
zero by the Receiver.
The transmit buffer can only be written when the DREIF Flag in the STATUS Register is set.
Data written to DATA when the DREIF Flag is not set, will be ignored by the USART Transmitter.
When data is written to the transmit buffer, and the Transmitter is enabled, the Transmitter will
load the data into the Transmit Shift Register when the Shift Register is empty. The data is then
transmitted on the TxD pin.
The receive buffer consists of a two level FIFO. The FIFO and the corresponding flags in the
Status Register (STATUS) will change state whenever the receive buffer is accessed (read).
Always read STATUS before DATA in order to get the correct flags.
• Bit 7 - RXCIF: USART Receive Complete Interrupt Flag
This flag is set when there are unread data in the receive buffer and cleared when the receive
buffer is empty (i.e., does not contain any unread data). When the Receiver is disabled, the
receive buffer will be flushed and consequently the RXCIF will become zero.
When interrupt-driven data reception is used, the receive complete interrupt routine must read
the received data from DATA in order to clear the RXCIF. If not, a new interrupt will occur
directly after the return from the current interrupt. This flag can also be cleared by writing a one
to its bit location.
Bit
+0x00
Read/Write
Initial Value
Bit
+0x01
Read/Write
Initial Value
RXCIF
R
7
0
R/W
7
0
TXCIF
R/W
6
0
”IRCOM - IR Communication Module” on page
R/W
6
0
DREIF
R
5
1
R/W
5
0
FERR
R
4
0
R/W
4
0
RXB[[7:0]
BUFOVF
TXB[[7:0]
R
3
0
R/W
3
0
PERR
R
2
0
R/W
2
0
1
–
R
0
220.
XMEGA D
R/W
1
0
RXB8
R/W
0
0
STATUS
R/W
0
0
213