ATMEGA64RZAV-10PU Atmel, ATMEGA64RZAV-10PU Datasheet - Page 317

• Manufacturer Part Number: ATMEGA64RZAV-10PU
• Description: MCU ATMEGA644/AT86RF230 40-DIP
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA64RZAV-10PU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 2kB EEPROM, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 40-DIP (0.600", 15.24mm)
• Wireless Frequency: 2.4 GHz
• Interface Type: JTAG, SPI
• Output Power: 3 dBm
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Applications: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: ATmega64

T
Note:
2593N–AVR–07/10
A
Symbol
I
V
I
t
CC
ACLK
ACID
ACIO
= -40⋅C to 85⋅C, V
1. "Max" means the highest value where the pin is guaranteed to be read as low
2. "Min" means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20 mA at VCC = 5V, 10 mA at VCC = 3V) under steady state
4. Although each I/O port can source more than the test conditions (20 mA at VCC = 5V, 10 mA at VCC = 3V) under steady
5. All DC Characteristics contained in this datasheet are based on simulation and characterization of other AVR microcon-
6. Values with “PRR – Power Reduction Register” disabled (0x00).
7. Power-down values includes Input Leakage Current.
conditions (non-transient), the following must be observed:
1.)The sum of all IOL, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2.)The sum of all IOL, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3.)The sum of all IOL, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4.)The sum of all IOL, for ports F0-F7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
state conditions (non-transient), the following must be observed:
1)The sum of all IOH, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2)The sum of all IOH, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3)The sum of all IOH, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4)The sum of all IOH, for ports F0-F7 should not exceed 100 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
trollers manufactured in the same process technology. These values are preliminary values representing design targets, and
will be updated after characterization of actual silicon
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
(7)
(6)
WDT disabled, V
V
V
V
Condition
Active 1 MHz, V
(ATmega644V)
Active 4 MHz, V
(ATmega644L)
Active 8 MHz, V
(ATmega644)
Idle 1 MHz, V
(ATmega644V)
Idle 4 MHz, V
(ATmega644L)
Idle 8 MHz, V
(ATmega644)
WDT enabled, V
V
V
V
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
CC
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
CC
= 2V
= 3V
= 5V
= 3V
= 3V
Min.
-50
(5)
Typ.
<10
750
500
0.4
<8
<2
Max.
0.15
0.5
2.7
9.0
0.7
2.5
20
40
50
3
ATmega644
(5)
Units
mA
mV
µA
nA
ns
317