ATMEGA64RZAV-10PU Atmel, ATMEGA64RZAV-10PU Datasheet - Page 302

• Manufacturer Part Number: ATMEGA64RZAV-10PU
• Description: MCU ATMEGA644/AT86RF230 40-DIP
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA64RZAV-10PU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 2kB EEPROM, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 40-DIP (0.600", 15.24mm)
• Wireless Frequency: 2.4 GHz
• Interface Type: JTAG, SPI
• Output Power: 3 dBm
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Applications: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: ATmega64

Table 25-17. Serial Programming Instruction Set (Hexadecimal values) (Continued)
Notes:
Figure 25-11. Serial Programming Instruction example
302
Instruction/Operation
Write EEPROM Memory Page (page access)
Write Lock bits
Write Fuse bits
Write Fuse High bits
Write Extended Fuse Bits
1. Not all instructions are applicable for all parts.
2. a = address.
3. Bits are programmed ‘0’, unprogrammed ‘1’.
4. To ensure future compatibility, unused Fuses and Lock bits should be unprogrammed (‘1’) .
5. Refer to the correspondig section for Fuse and Lock bits, Calibration and Signature bytes and Page size.
6. See htt://www.atmel.com/avr for Application Notes regarding programming and programmers.
ATmega644
Byte 1
Load Program Memory Page (High/Low Byte)/
Load EEPROM Memory Page (page access)
Bit 15 B
Byte 2
Adr MSB
Adr dr M
A
r MS S B
If the LSB in RDY/BSY data byte out is ‘1’, a programming operation is still pending. Wait until
this bit returns ‘0’ before the next instruction is carried out.
Within the same page, the low data byte must be loaded prior to the high data byte.
After data is loaded to the page buffer, program the EEPROM page, see
302.
Byte 3
Adr LSB
Page Offset
0
Serial Programming Instruction
Byte 4
Byte 1
$C2
$AC
$AC
$AC
$AC
Program Memory/
EEPROM Memory
Page Buffer
Page N-1
Page 0
Page 1
Page 2
Byte 1
0000 00aa
Byte 2
$E0
$A0
$A8
$A4
Page Number
Instruction Format
Bit 15 B
Write Program Memory Page/
Write EEPROM Memory Page
Byte 2
Adr MSB
aaaa aa00
Byte 3
$00
$00
$00
$00
Byte 3
Adr LSB
A A dr dr LS
LSB
SB
Figure 25-11 on page
0
data byte in
data byte in
data byte in
data byte in
Byte 4
2593N–AVR–07/10
Byte 4
$00