HD64F2676VFC33 Renesas Electronics America, HD64F2676VFC33 Datasheet - Page 854
HD64F2676VFC33
Manufacturer Part Number
HD64F2676VFC33
Description
IC H8S MCU FLASH 256K 144-QFP
Manufacturer
Renesas Electronics America
Series
H8® H8S/2600r
Specifications of HD64F2676VFC33
Core Processor
H8S/2600
Core Size
16-Bit
Speed
33MHz
Connectivity
IrDA, SCI
Peripherals
DMA, POR, PWM, WDT
Number Of I /o
103
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 12x10b; D/A 4x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
144-QFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HD64F2676VFC33
Manufacturer:
RENESAS
Quantity:
5 530
Company:
Part Number:
HD64F2676VFC33
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
HD64F2676VFC33V
Manufacturer:
RENESAS
Quantity:
5 530
Company:
Part Number:
HD64F2676VFC33V
Manufacturer:
ROHM
Quantity:
750 000
Part Number:
HD64F2676VFC33V
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
- Current page: 854 of 981
- Download datasheet (6Mb)
Section 19 Flash Memory (F-ZTAT Version)
19.12
Precautions concerning the use of on-board programming mode, the RAM emulation function, and
programmer mode are summarized below.
1. Use the specified voltages and timing for programming and erasing.
2. Reset the flash memory before turning on/off the power.
3. Powering on and off.
4. FWE application/disconnection.
The following points must be observed concerning FWE application and disconnection to prevent
unintentional programming or erasing of flash memory:
Rev. 3.00 Mar 17, 2006 page 802 of 926
REJ09B0283-0300
Applied voltages in excess of the rating can permanently damage the device. Use a PROM
programmer that supports the Renesas Technology microcomputer device type with 512-kbyte
on-chip flash memory (FZTAT512V3A).
Do not select the HN27C4096 setting for the PROM programmer, and only use the specified
socket adapter.
When applying or disconnecting Vcc power, fix the RES pin low and place the flash memory
in the hardware protection state. The power-on and power-off timing requirements should also
be satisfied in the event of a power failure and subsequent recovery.
Do not apply a high level to the FWE pin until V
before turning off V
When applying or disconnecting V
in the hardware protection state.
The power-on and power-off timing requirements should also be satisfied in the event of a
power failure and subsequent recovery. The power-on and power-off timing in the H8S/2678
Group is shown in figure 19.12.
FWE application should be carried out when this LSI operation is in a stable condition. If this
LSI operation is not stable, fix the FWE pin low and set the protection state.
Apply FWE when the V
In boot mode, apply and disconnect FWE during a reset.
In user program mode, FWE can be switched between high and low level regardless of the
reset state. FWE input can also be switched during execution of a program in flash memory.
Do not apply FWE if program runaway has occurred.
Disconnect FWE only when the SWE, ESU, PSU, EV, PV, and E bits in FLMCR1 are cleared.
Usage Notes
CC
.
CC
voltage has stabilized within its rated voltage range.
CC
power, fix the FWE pin low and place the flash memory
CC
has stabilized. Also, drive the FWE pin low
Related parts for HD64F2676VFC33
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: