HD64F2676VFC33 Renesas Electronics America, HD64F2676VFC33 Datasheet - Page 383

IC H8S MCU FLASH 256K 144-QFP

HD64F2676VFC33

Manufacturer Part Number
HD64F2676VFC33
Description
IC H8S MCU FLASH 256K 144-QFP
Manufacturer
Renesas Electronics America
Series
H8® H8S/2600r
Datasheets

Specifications of HD64F2676VFC33

Core Processor
H8S/2600
Core Size
16-Bit
Speed
33MHz
Connectivity
IrDA, SCI
Peripherals
DMA, POR, PWM, WDT
Number Of I /o
103
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 12x10b; D/A 4x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
144-QFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
HD64F2676VFC33
Manufacturer:
RENESAS
Quantity:
5 530
Part Number:
HD64F2676VFC33
Quantity:
9 520
Part Number:
HD64F2676VFC33
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
HD64F2676VFC33V
Manufacturer:
RENESAS
Quantity:
5 530
Part Number:
HD64F2676VFC33V
Manufacturer:
ROHM
Quantity:
750 000
Part Number:
HD64F2676VFC33V
Manufacturer:
RENESAS
Quantity:
120
Part Number:
HD64F2676VFC33V
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
7.7.2
When the MSTP13 bit in MSTPCRH is set to 1, the DMAC clock stops, and the module stop state
is entered. However, 1 cannot be written to the MSTP13 bit if any of the DMAC channels is
enabled. This setting should therefore be made when DMAC operation is stopped.
When the DMAC clock stops, DMAC register accesses can no longer be made. Since the
following DMAC register settings are valid even in the module stop state, they should be
invalidated, if necessary, before a module stop.
7.7.3
When the WDBE bit of BCR in the bus controller is set to 1, enabling the write data buffer
function, dual address transfer external write cycles or single address transfers and internal
accesses (on-chip memory or internal I/O registers) are executed in parallel.
If a DMAC transfer cycle occurs immediately after a DMAC register read cycle, the DMAC
register is read as shown in figure 7.40.
Transfer end/break interrupt (DTE = 0 and DTIE = 1)
TEND pin enable (TEE = 1)
DACK pin enable (FAE = 0 and SAE = 1)
DMA internal
address
DMA control
DMA register
operation
Module Stop
Write Data Buffer Function
Note: The lower word of MAR is the updated value after the operation in [1].
Figure 7.40 Contention between DMAC Register Update and CPU Read
MAR upper
word read
Idle
CPU longword read
[1]
MAR lower
word read
Transfer
source
Read
[2]
Rev. 3.00 Mar 17, 2006 page 331 of 926
DMA read
destination
DMA transfer cycle
Transfer
Write
Section 7 DMA Controller (DMAC)
DMA write
Idle
REJ09B0283-0300

Related parts for HD64F2676VFC33