HD64F2676VFC33 Renesas Electronics America, HD64F2676VFC33 Datasheet - Page 772

• Manufacturer Part Number: HD64F2676VFC33
• Description: IC H8S MCU FLASH 256K 144-QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2600r

Specifications of HD64F2676VFC33

• Core Processor: H8S/2600
• Core Size: 16-Bit
• Speed: 33MHz
• Connectivity: IrDA, SCI
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 103
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 4x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 144-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Section 15 Serial Communication Interface (SCI, IrDA)
As in the above sample start character, with the direct convention type, the logic 1 level
corresponds to state Z and the logic 0 level to state A, and transfer is performed in LSB-first order.
The start character data above is H'3B. For the direct convention type, clear the SDIR and SINV
bits in SCMR to 0. According to the Smart Card regulations, clear the O/E bit in SMR to 0 to
select even parity mode.
With the inverse convention type, the logic 1 level corresponds to state A and the logic 0 level to
state Z, and transfer is performed in MSB-first order. The start character data above is H'3F. For
the inverse convention type, set the SDIR and SINV bits in SCMR to 1. According to the Smart
Card regulations, even parity mode is the logic 0 level of the parity bit, and corresponds to state Z.
In this LSI, the SINV bit inverts only data bits D7 to D0. Therefore, set the O/E bit in SMR to 1 to
invert the parity bit for both transmission and reception.
15.7.3
Operation in block transfer mode is the same as that in normal Smart Card interface, except for the
following points.
15.7.4
Only the internal clock generated by the on-chip baud rate generator is used as transmit/receive
clock in Smart Card interface. In Smart Card interface mode, the SCI operates on a basic clock
with a frequency of 32, 64, 372, or 256 times the bit rate (fixed at 16 times in normal
asynchronous mode) as determined by bits BCP1 and BCP0. In reception, the SCI samples the
Rev. 3.00 Mar 17, 2006 page 720 of 926
REJ09B0283-0300
In reception, though the parity check is performed, no error signal is output even if an error is
detected. However, the PER bit in SSR is set to 1 and must be cleared before receiving the
parity bit of the next frame.
In transmission, a guard time of at least 1 etu is left between the end of the parity bit and the
start of the next frame.
In transmission, because retransmission is not performed, the TEND flag is set to 1, 11.5 etu
after transmission start.
As with the normal Smart Card interface, the ERS flag indicates the error signal status, but
since error signal transfer is not performed, this flag is always cleared to 0.
Block Transfer Mode
Receive Data Sampling Timing and Reception Margin
(Z)
Figure 15.24 Inverse Convention (SDIR = SINV = O/E E E E = 1)
Ds
A
D7 D6 D5 D4 D3 D2 D1 D0 Dp
Z
Z
A
A
A
A
A
A
Z
(Z) State