SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 828

no-image

SAM3U2C

Manufacturer Part Number
SAM3U2C
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM3U2C

Flash (kbytes)
128 Kbytes
Pin Count
100
Max. Operating Frequency
96 MHz
Cpu
Cortex-M3
# Of Touch Channels
28
Hardware Qtouch Acquisition
No
Max I/o Pins
57
Ext Interrupts
57
Usb Transceiver
1
Quadrature Decoder Channels
1
Usb Speed
Hi-Speed
Usb Interface
Device
Spi
4
Twi (i2c)
1
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
12
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
36
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
828
828
SAM3U Series
SAM3U Series
7. Poll CBTC[x] bit in the DMAC_EBCISR Register.
8. If a new list of buffers shall be transferred, repeat step 6. Check and handle HSMCI
9. Poll FIFOEMPTY field in the HSMCI_SR.
a. Read the channel Register to choose an available (disabled) channel.
b. Clear any pending interrupts on the channel from the previous DMAC transfer by
c. Program a List of descriptors.
d. The LLI(n).DMAC_SADDRx memory location for channel x must be set to the loca-
e. The LLI(n).DMAC_DADDRx register for channel x must be set with the starting
f.
g. Program LLI(n).DMAC_CTRLBx register for channel x with the following field’s
h. Program LLI(n).DMAC_CFGx register for channel x with the following field’s values:
i.
j.
k. Program DMAC_DSCRx for channel register x with the address of the first descrip-
l.
errors.
reading the DMAC_EBCISR register.
tion of the source data. When the first data location is not word aligned, the two
LSB bits define the temporary value called dma_offset. The two LSB bits of
LLI(n).DMAC_SADDRx must be set to 0.
address of the HSMCI_FIFO address.
Program LLI(n).DMAC_CTRLAx register of channel x with the following field’s
values:
–DST_WIDTH is set to WORD.
–SRC_WIDTH is set to WORD.
–DCSIZE must be set according to the value of HSMCI_DMA, CHKSIZE field.
–BTSIZE is programmed with CEILING((block_length + dma_offset)/4).
values:
–DST_INCR is set to INCR.
–SRC_INCR is set to INCR.
–DST_DSCR is set to 0 (fetch operation is enabled for the destination).
–SRC_DSCR is set to 1 (source address is contiguous).
–FC field is programmed with memory to peripheral flow control mode.
–Both DST_DSCR and SRC_DSCR are set to 1 (descriptor fetch is disabled).
–DIF and SIF are set with their respective layer ID. If SIF is different from DIF, DMA
–FIFOCFG defines the watermark of the DMA channel FIFO.
–DST_H2SEL is set to true to enable hardware handshaking on the destination.
–SRC_REP is set to 0. (contiguous memory access at block boundary)
–DST_PER is programmed with the hardware handshaking ID of the targeted
If LLI(n) is the last descriptor, then LLI(n).DSCR points to 0 else LLI(n) points to the
start address of LLI(n+1).
the LLI fetch operation.
tor LLI(0).
for request.
Program DMAC_CTRLBx for channel register x with 0. Its content is updated with
Enable Channel x writing one to DMAC_CHER[x]. The DMA is ready and waiting
Controller is able to prefetch data and write HSMCI simultaneously.
HSMCI Host Controller.
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11

Related parts for SAM3U2C