SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 496

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

28.14.17 PMC Fast Startup Mode Register
Name:
Address:
Access:
This register can only be written if the WPEN bit is cleared in the
• FSTT0 - FSTT15: Fast Startup Input Enable 0 to 15
0 = The corresponding wake up input has no effect on the Power Management Controller.
1 = The corresponding wake up input enables a fast restart signal to the Power Management Controller.
• RTTAL: RTT Alarm Enable
0 = The RTT alarm has no effect on the Power Management Controller.
1 = The RTT alarm enables a fast restart signal to the Power Management Controller.
• RTCAL: RTC Alarm Enable
0 = The RTC alarm has no effect on the Power Management Controller.
1 = The RTC alarm enables a fast restart signal to the Power Management Controller.
• USBAL: USB Alarm Enable
0 = The USB alarm has no effect on the Power Management Controller.
1 = The USB alarm enables a fast restart signal to the Power Management Controller.
• LPM: Low Power Mode
0 = The WaitForInterrupt (WFI) or WaitForEvent (WFE) instruction of the processor makes the processor enter in Idle
Mode.
1 = The WaitForEvent (WFE) instruction of the processor makes the system enter in Wait Mode.
496
FSTT15
FSTT7
31
23
15
–
–
7
SAM3U Series
0x400E0470
PMC_FSMR
Read-write
FSTT14
FSTT6
30
22
14
–
–
6
FSTT13
FSTT5
29
21
13
–
–
5
FSTT12
FSTT4
LPM
28
20
12
–
4
“PMC Write Protect Mode
FSTT11
FSTT3
27
19
11
–
–
3
FSTT10
USBAL
FSTT2
26
18
10
–
2
Register”.
RTCAL
FSTT9
FSTT1
25
17
–
9
1
6430E–ATARM–29-Aug-11
FSTT8
FSTT0
RTTAL
24
16
–
8
0