SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 634

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 33-10. Master Read with Multiple Data Bytes
33.8.6
33.8.6.1
634
634
TXCOMP
RXRDY
TWD
SAM3U Series
SAM3U Series
Internal Address
S
7-bit Slave Addressing
Write START Bit
DADR
RXRDY is used as Receive Ready for the PDC receive channel.
The TWI interface can perform various transfer formats: Transfers with 7-bit slave address
devices and 10-bit slave address devices.
When Addressing 7-bit slave devices, the internal address bytes are used to perform random
address (read or write) accesses to reach one or more data bytes, within a memory page loca-
tion in a serial memory, for example. When performing read operations with an internal address,
the TWI performs a write operation to set the internal address into the slave device, and then
switch to Master Receiver mode. Note that the second start condition (after sending the IADR) is
sometimes called “repeated start” (Sr) in I
Figure 33-11
The three internal address bytes are configurable through the Master Mode register
(TWI_MMR).
If the slave device supports only a 7-bit address, i.e. no internal address, IADRSZ must be set to
0.
In the figures below the following abbreviations are used:
• S
• Sr
• P
• W
• R
• A
• N
• DADR
• IADR
R
A
and
Start
Repeated Start
Stop
Write
Read
Acknowledge
Not Acknowledge
Device Address
Internal Address
DATA n
Figure 33-13
Read RHR
A
DATA n
for Master Write operation with internal address.
DATA (n+1)
2
C fully-compatible devices. See
A
DATA (n+1)
Read RHR
DATA (n+m)-1
DATA (n+m)-1
A
Read RHR
after next-to-last data read
DATA (n+m)
Write STOP Bit
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
Figure
N
33-12. See
DATA (n+m)
Read RHR
P