SAM3U2C Atmel Corporation, SAM3U2C Datasheet - Page 1026

• Manufacturer Part Number: SAM3U2C
• Manufacturer: Atmel Corporation

Specifications of SAM3U2C

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 28
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 57
• Ext Interrupts: 57
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 4
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

40.3.3.3
40.3.4
40.3.4.1
40.3.4.2
1026
SAM3U Series
DMAC Transfer Types
Single Transactions
Multi-buffer Transfers
Buffer Chaining Using Linked Lists
Writing a 1 to the DMAC_SREQ[2x] register starts a source single transaction request, where x
is the channel number. Writing a 1 to the DMAC_SREQ[2x+1] register starts a destination single
transfer request, where x is the channel number.
Upon completion of the chunk transaction, the hardware clears the DMAC_SREQ[x] or
DMAC_SREQ[2x+1].
Software can poll the relevant channel bit in the DMAC_CREQ[2x]/DMAC_CREQ[2x+1] and
DMAC_SREQ[x]/DMAC_SREQ[2x+1] registers. When both are 0, then either the requested
chunk or single transaction has completed.
A DMAC transfer may consist of single or multi-buffers transfers. On successive buffers of a
multi-buffer transfer, the DMAC_SADDRx/DMAC_DADDRx registers in the DMAC are repro-
grammed using either of the following methods:
On successive buffers of a multi-buffer transfer, the DMAC_CTRLAx and DMAC_CTRLBx regis-
ters in the DMAC are re-programmed using either of the following methods:
When buffer chaining, using linked lists is the multi-buffer method of choice, and on successive
buffers, the DMAC_DSCRx register in the DMAC is re-programmed using the following method:
A buffer descriptor (LLI) consists of following registers, DMAC_SADDRx, DMAC_DADDRx,
DMAC_DSCRx, DMAC_CTRLAx, DMAC_CTRLBx.These registers, along with the
DMAC_CFGx register, are used by the DMAC to set up and describe the buffer transfer.
In this case, the DMAC re-programs the channel registers prior to the start of each buffer by
fetching the buffer descriptor for that buffer from system memory. This is known as an LLI
update.
DMAC buffer chaining is supported by using a Descriptor Pointer register (DMAC_DSCRx) that
stores the address in memory of the next buffer descriptor. Each buffer descriptor contains the
corresponding buffer descriptor (DMAC_SADDRx, DMAC_DADDRx, DMAC_DSCRx,
DMAC_CTRLAx DMAC_CTRLBx).
To set up buffer chaining, a sequence of linked lists must be programmed in memory.
The DMAC_SADDRx, DMAC_DADDRx, DMAC_DSCRx, DMAC_CTRLAx and DMAC_CTRLBx
registers are fetched from system memory on an LLI update. The updated content of the
DMAC_CTRLAx register is written back to memory on buffer completion.
1027
fer chaining.
The Linked List multi-buffer transfer is initiated by programming DMAC_DSCRx with DSCRx(0)
(LLI(0) base address) and DMAC_CTRLBx register with both SRC_DSCR and DST_DSCR set
• Buffer chaining using linked lists
• Contiguous address between buffers
• Buffer chaining using linked lists
• Buffer chaining using linked lists
shows how to use chained linked lists in memory to define multi-buffer transfers using buf-
Figure 40-4 on page
6430E–ATARM–29-Aug-11