C8051F902-GM Silicon Laboratories Inc, C8051F902-GM Datasheet - Page 89

• Manufacturer Part Number: C8051F902-GM
• Description: IC MCU 8BIT 8KB FLASH 24QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F902-GM

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 24-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 15x10/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Ram Size: 768 B
• Interface Type: UART
• Maximum Clock Frequency: 25 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F912DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit
• Package: 24QFN EP
• Device Core: 8051
• Family Name: C8051F90x
• Maximum Speed: 25 MHz
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1848-5

7.2.
When a comparator is enabled, its output is a logic 1 if the voltage at the positive input is higher than the
voltage at the negative input. When disabled, the comparator output is a logic 0. The comparator output is
synchronized with the system clock as shown in Figure 7.2. The synchronous “latched” output (CP0, CP1)
can be polled in software (CPnOUT bit), used as an interrupt source, or routed to a Port pin (configured for
digital I/O) through the Crossbar.
The asynchronous “raw” comparator output (CP0A, CP1A) is used by the low power mode wake-up logic
and reset decision logic. See the Power Options chapter and the Reset Sources chapter for more details
on how the asynchronous comparator outputs are used to make wake-up and reset decisions. The
asynchronous comparator output can also be routed directly to a Port pin through the Crossbar, and is
available for use outside the device even if the system clock is stopped.
When using a Comparator as an interrupt source, Comparator interrupts can be generated on rising-edge
and/or falling-edge comparator output transitions. Two independent interrupt flags (CPnRIF and CPnFIF)
allow software to determine which edge caused the Comparator interrupt. The comparator rising-edge and
falling-edge interrupt flags are set by hardware when a corresponding edge is detected regardless of the
interrupt enable state. Once set, these bits remain set until cleared by software.
The rising-edge and falling-edge interrupts can be individually enabled using the CPnRIE and CPnFIE
interrupt enable bits in the CPTnMD register. In order for the CPnRIF and/or CPnFIF interrupt flags to
generate an interrupt request to the CPU, the Comparator must be enabled as an interrupt source and
global interrupts must be enabled. See the Interrupt Handler chapter for additional information.
Analog Input Multiplexer
Px.x
Px.x
Px.x
Px.x
Comparator Outputs
Figure 7.2. Comparator 1 Functional Block Diagram
CP1HYP1
CP1HYP0
CP1HYN1
CP1HYN0
CP1OUT
CP1RIF
CP1EN
CP1FIF
CP1 +
CP1 -
+
-
Rev. 1.0
VDD
GND
Decision
C8051F91x-C8051F90x
Reset
CPT0MD
Tree
(ASYNCHRONOUS)
(SYNCHRONIZER)
D
SET
CLR
Q
Q
D
SET
CLR
Q
Q
Rising-edge
CP1
Crossbar
Interrupt
Logic
Falling-edge
Interrupt
CP1
CP1A
CP1
CP1
89