AT91SAM7L64-AU Atmel, AT91SAM7L64-AU Datasheet - Page 365

• Manufacturer Part Number: AT91SAM7L64-AU
• Description: MCU ARM7 64K HS FLASH 128-LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7L64-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 36MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 1.55 V ~ 1.8 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 128-LQFP
• Controller Family/series: AT91SAM7xxx
• No. Of I/o's: 80
• Ram Memory Size: 6KB
• Cpu Speed: 36MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 6 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 80
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7L-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: AT91SAM7L-STK - KIT EVAL FOR AT91SAM7LAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

30.5
30.5.1
30.5.2
30.5.3
6257A–ATARM–20-Feb-08
Product Dependencies
I/O Lines
Power Management
Interrupt
The pins used for interfacing the USART may be multiplexed with the PIO lines. The program-
mer must first program the PIO controller to assign the desired USART pins to their peripheral
function. If I/O lines of the USART are not used by the application, they can be used for other
purposes by the PIO Controller.
To prevent the TXD line from falling when the USART is disabled, the use of an internal pull up
is mandatory. If the hardware handshaking feature or Modem mode is used, the internal pull up
on TXD must also be enabled.
All the pins of the modems may or may not be implemented on the USART. Only
equipped with all the modem signals. On USARTs not equipped with the corresponding pin, the
associated control bits and statuses have no effect on the behavior of the USART.
The USART is not continuously clocked. The programmer must first enable the USART Clock in
the Power Management Controller (PMC) before using the USART. However, if the application
does not require USART operations, the USART clock can be stopped when not needed and be
restarted later. In this case, the USART will resume its operations where it left off.
Configuring the USART does not require the USART clock to be enabled.
The USART interrupt line is connected on one of the internal sources of the Advanced Interrupt
Controller. Using the USART interrupt requires the AIC to be programmed first. Note that it is not
recommended to use the USART interrupt line in edge sensitive mode.
AT91SAM7L128/64 Preliminary
USART1
fully
365