ST92F150CV1QB STMicroelectronics, ST92F150CV1QB Datasheet - Page 106

• Manufacturer Part Number: ST92F150CV1QB
• Description: MCU 8BIT 128K FLASH 100PQFP
• Manufacturer: STMicroelectronics
• Series: ST9r

Specifications of ST92F150CV1QB

• Core Processor: ST9
• Core Size: 8/16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 77
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 100-QFP
• Processor Series: ST92F15x
• Core: ST9
• Data Bus Width: 8 bit, 16 bit
• Data Ram Size: 6 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 80
• Number Of Timers: 5 x 16 bit
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST92F150-EPB
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit x 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-4882

ST92F124/F150/F250 - INTERRUPTS
5.11 INTERRUPT REGISTERS
CENTRAL INTERRUPT CONTROL REGISTER
(CICR)
R230 - Read/Write
Register Group: System
Reset value: 1000 0111 (87h)
Bit 7 = GCEN: Global Counter Enable.
This bit enables the 16-bit Multifunction Timer pe-
ripheral.
0: MFT disabled
1: MFT enabled
Bit 6 = TLIP: Top Level Interrupt Pending.
This bit is set by hardware when Top Level Inter-
rupt (TLI) trigger event occurs. It is cleared by
hardware when a TLI is acknowledged. It can also
be set by software to implement a software TLI.
0: No TLI pending
1: TLI pending
Bit 5 = TLI: Top Level Interrupt.
This bit is set and cleared by software.
0: A Top Level Interrupt is generared when TLIP is
1: A Top Level Interrupt request is generated when
Bit 4 = IEN: Interrupt Enable.
This bit is cleared by the interrupt machine cycle
(except for a TLI).
It is set by the iret instruction (except for a return
from TLI).
It is set by the EI instruction.
It is cleared by the DI instruction.
0: Maskable interrupts disabled
1: Maskable Interrupts enabled
Note: The IEN bit can also be changed by soft-
ware using any instruction that operates on regis-
ter CICR, however in this case, take care to avoid
spurious interrupts, since IEN cannot be cleared in
the middle of an interrupt arbitration. Only modify
106/429
GCEN TLIP
9
set, only if TLNM=1 in the NICR register (inde-
pendently of the value of the IEN bit).
IEN=1 and the TLIP bit are set.
7
TLI
IEN
IAM CPL2 CPL1 CPL0
0
the IEN bit when interrupts are disabled or when
no peripheral can generate interrupts. For exam-
ple, if the state of IEN is not known in advance,
and its value must be restored from a previous
push of CICR on the stack, use the sequence DI;
POP CICR to make sure that no interrupts are be-
ing arbitrated when CICR is modified.
Bit 3 = IAM: Interrupt Arbitration Mode.
This bit is set and cleared by software.
0: Concurrent Mode
1: Nested Mode
Bits 2:0 = CPL[2:0]: Current Priority Level.
These bits define the Current Priority Level.
CPL=0 is the highest priority. CPL=7 is the lowest
priority. These bits may be modified directly by the
interrupt hardware when Nested Interrupt Mode is
used.
EXTERNAL INTERRUPT TRIGGER REGISTER
(EITR)
R242 - Read/Write
Register Page: 0
Reset value: 0000 0000 (00h)
Bit 7 = TED1: INTD1 Trigger Event
Bit 6 = TED0: INTD0 Trigger Event
Bit 5 = TEC1: INTC1 Trigger Event
Bit 4 = TEC0: INTC0 Trigger Event
Bit 3 = TEB1: INTB1 Trigger Event
Bit 2 = TEB0: INTB0 Trigger Event
Bit 1 = TEA1: INTA1 Trigger Event
Bit 0 = TEA0: INTA0 Trigger Event
These bits are set and cleared by software.
0: Select falling edge as interrupt trigger event
1: Select rising edge as interrupt trigger event
TED1 TED0 TEC1 TEC0 TEB1 TEB0 TEA1 TEA0
7
0