TMPM333FDFG Toshiba, TMPM333FDFG Datasheet - Page 221

• Manufacturer Part Number: TMPM333FDFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 512K FLASH, 32K SRAM
• Manufacturer: Toshiba

Specifications of TMPM333FDFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 512K
• Rom Type: Flash
• Ram (kbytes): 32K
• Number Of Pins: 100
• Package: LQFP(14×14)
• Vcc: 3V
• Cpu Mhz: 40
• Ssp (ch) Spi: -
• I2c/sio (ch): 3
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: -
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: 12
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 10
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: -
• Hardware Cec Controller: -
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit
• Lead Free Status / Rohs Status: Details

9.5.4
9.5.5
9.5.6
9.5.7
9.5.8
9.5.9
TBxCP1 capture registers. The timing with which to latch data is specified by TBxMOD<TBCPM[1:0]>.
values are taken into the TBxCP0 capture register each time "0" is written to TBxMOD<TBCP>.
the TBxUC registers.
TBxRG1) to detect whether there is a match or not. If a match is detected, INTTBx is generated.
registers. It can be enabled or disabled to reverse by setting the TBxFFCR<TBC1T1, TBC0T1, TBE1T1,
TBE0T1>.
TBxFFCR<TBFF0C[1:0]>. It can be set to "1" by writing "01," and can be cleared to "0" by writing "10."
corresponding port settings must be programmed beforehand.
into the TBxCP0 and TBxCP1 capture registers. The interrupt timing is specified by the CPU.
Capture
Capture registers (TBxCP0, TBxCP1)
Up-counter capture register (TBxUC)
Comparators (CP0, CP1)
Timer Flip-flop (TBxFF0)
Capture interrupt (INTCAPx0, INTCAPx1)
This is a circuit that controls the timing of latching values from the UC up-counter into the TBxCP0 and
Software can also be used to import values from the UC up-counter into the capture register; specifically, UC
This register captures an up-counter (UC) value.
Other than the capturing functions shown above, the current count value of the UC can be captured by reading
This register compares with the up-counter (UC) and the value setting of the Timer Register (TBxRG0 and
The timer flip-flop (TBxFF0) is reversed by a match signal from the comparator and a latch signal to the capture
The value of TBxFF0 becomes undefined after a reset. The flip-flop can be reversed by writing "00" to
The value of TBxFF0 can be output to the Timer output pin (TBxOUT). If the timer output is performed, the
Interrupts INTCAPx0 and INTCAPx1 can be generated at the timing of latching values from the UC up-counter
Page 201
TMPM333FDFG/FYFG/FWFG