MCF5282CVM80 Freescale Semiconductor, MCF5282CVM80 Datasheet - Page 692

• Manufacturer Part Number: MCF5282CVM80
• Description: IC MPU 512K 80MHZ 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5282CVM80

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 150
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• Ram Memory Size: 64KB
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Digital Ic Case Style: MAPBGA
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Electrical Characteristics
33.6
33-8
6
7
8
9
10
11
1
2
3
4
5
6
Analog Supply, with reference to V
Internal Digital Supply
Reference Supply, with reference to V
V
V
V
V
V
V
Maximum Input Current
Load Capacitance determined from crystal manufacturer specifications and will include circuit board parasitics.
This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the
synthesizer control register (SYNCR).
Assuming a reference is available at power up, lock time is measured from the time V
RSTO negating. If the crystal oscillator is being used as the reference for the PLL, then the crystal start up time
must be added to the PLL lock time to determine the total start-up time.
PLL is operating in 1:1 PLL mode.
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal.
Noise injected into the PLL circuitry via V
Cjitter percentage for a given interval
Based on slow system clock of 40 MHz measured at f
SS
DD
REF
RH
RL
DDH
For internal digital supply of V
Refers to allowed random sequencing of power supplies.
Refers to allowed random sequencing of power supplies.
Transitions within the limit do not affect device reliability or cause permanent damage. Exceeding limit may cause
permanent conversion error on stressed channels and on unstressed channels.
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor,
calculate resistance values using V
calculated values.
Condition applies to one pin at a time.
Differential Voltage
to V
Differential Voltage
to V
Differential Voltage
to V
QADC Electrical Characteristics
SSA
DDA
DDA
Differential Voltage
Differential Voltage
Differential Voltage
Parameter
1
, with reference to V
2
4, 5, 6
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
DD
Table 33-9. QADC Absolute Maximum Ratings
3
SSA
= 3.3V typical.
POSCLAMP
RL
DDPLL
SS
= V
and V
DDA
SSPLL
sys
+ 0.3V and V
V
V
V
V
V
V
DDH
max.
DD
RH
SS
Symbol
RL
RH
V
and variation in crystal oscillator frequency increase the
V
V
I
– V
– V
– V
– V
DDA
MA
DD
RH
– V
– V
SSA
DDA
DDA
SSA
RL
DDA
NEGCLAMP
–0.3
–0.3
–0.3
–0.1
–6.0
–0.3
–6.0
–0.3
–1.0
Min
–25
= –0.3 V, then use the larger of the
DD
and V
Max
6.0
4.0
6.0
0.1
4.0
6.0
6.0
0.3
1.0
25
DDPLL
Freescale Semiconductor
are valid to
Unit
mA
V
V
V
V
V
V
V
V
V
sys
.