MCF5282CVM80 Freescale Semiconductor, MCF5282CVM80 Datasheet - Page 302

• Manufacturer Part Number: MCF5282CVM80
• Description: IC MPU 512K 80MHZ 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5282CVM80

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 150
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• Ram Memory Size: 64KB
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Digital Ic Case Style: MAPBGA
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

DMA Controller Module
16.4.2
DARn, shown in
16-6
Address
Address
Reset
Reset
Field
Field
R/W
R/W
Destination Address Registers (DAR0–DAR3)
31
31
The backdoor enable bit must be set in both the core and SCM in order to
enable backdoor accesses from the DMA to SRAM. See
“Memory Base Address Register
Flash accesses (reads/writes) by a bus master other than the core (DMA
controller or Fast Ethernet Controller), or writes to Flash by the core during
programming, must use the backdoor Flash address of IPSBAR plus an
offset of 0x0400_0000. For example, for a DMA transfer from the first
Flash location when IPSBAR is still at its default location of 0x4000_0000,
the source register would be loaded with 0x4400_0000. Backdoor Flash
read accesses can be made with the bus master, but it takes two cycles longer
than a direct read of the Flash when using the FLASHBAR address.
The DMA does not maintain coherency with the cache. Therefore, DMAs
should not transfer data to cacheable memory unless software is used to
maintain the cache coherency.
The DMA should not be used to write data to the UART transmit FIFO in
cycle steal mode. When the UART interrupt is used as a DMA request it
does not negate fast enough to get a single transfer. The UART transmit
FIFO only has one entry so the data from the second byte would be lost.
Figure
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
16-5, holds the address to which the DMA controller sends data.
Figure 16-5. Destination Address Registers (DARn)
Figure 16-4. Source Address Registers (SARn)
0000_0000_0000_0000_0000_0000_0000_0000
0000_0000_0000_0000_0000_0000_0000_0000
IPSBAR + 0x100, 0x140, 0x180, 0x1C0
IPSBAR + 0x104, 0x144, 0x184, 0x1C4
(RAMBAR)” for more details.
NOTE
NOTE
NOTE
NOTE
SAR
DAR
R/W
R/W
Section 8.4.2,
Freescale Semiconductor
0
0