MA180023 Microchip Technology, MA180023 Datasheet - Page 58

• Manufacturer Part Number: MA180023
• Description: MODULE PLUG-IN PIC18F46J11 PIM
• Manufacturer: Microchip Technology
• Series: PIC®r

Specifications of MA180023

• Accessory Type: Plug-In Module (PIM) - PIC18F46J11
• Tool / Board Applications: General Purpose MCU, MPU, DSP, DSC
• Mcu Supported Families: PIC18
• Supported Devices: Stand-alone Or W/ HPC(DM183022) Or PIC18(DM183032)
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC18
• Silicon Core Number: PIC18F
• Silicon Family Name: PIC18FxxJxx
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: HPC Explorer Board (DM183022) or PIC18 Explorer Board (DM183032)
• For Use With: DM183032 - BOARD EXPLORER PICDEM PIC18DM183022 - BOARD DEMO PIC18FXX22 64/80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F46J11 FAMILY
REGISTER 4-1:
DS39932C-page 58
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1: It is recommended that the POR bit be set after a Power-on Reset has been detected, so that subsequent
R/W-0
IPEN
2: If the on-chip voltage regulator is disabled, BOR remains ‘0’ at all times. See Section 4.4.1 “Detecting
3: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming that POR was set to
Power-on Resets may be detected.
BOR” for more information.
‘1’ by software immediately after a Power-on Reset).
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)
Unimplemented: Read as ‘0’
CM: Configuration Mismatch Flag bit
1 = A Configuration Mismatch Reset has not occurred
0 = A Configuration Mismatch Reset has occurred (must be set in software after a Configuration
RI: RESET Instruction Flag bit
1 = The RESET instruction was not executed (set by firmware only)
0 = The RESET instruction was executed causing a device Reset (must be set in software after a
TO: Watchdog Time-out Flag bit
1 = Set by power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-Down Detection Flag bit
1 = Set by power-up or by the CLRWDT instruction
0 = Set by execution of the SLEEP instruction
POR: Power-on Reset Status bit
1 = A Power-on Reset has not occurred (set by firmware only)
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
BOR: Brown-out Reset Status bit
1 = A Brown-out Reset has not occurred (set by firmware only)
0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
Mismatch Reset occurs)
Brown-out Reset occurs)
U-0
—
RCON: RESET CONTROL REGISTER (ACCESS FD0h)
W = Writable bit
‘1’ = Bit is set
R/W-1
CM
R/W-1
RI
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-1
TO
R-1
PD
© 2009 Microchip Technology Inc.
x = Bit is unknown
R/W-0
POR
R/W-0
BOR
bit 0