MA180023 Microchip Technology, MA180023 Datasheet - Page 166

• Manufacturer Part Number: MA180023
• Description: MODULE PLUG-IN PIC18F46J11 PIM
• Manufacturer: Microchip Technology
• Series: PIC®r

Specifications of MA180023

• Accessory Type: Plug-In Module (PIM) - PIC18F46J11
• Tool / Board Applications: General Purpose MCU, MPU, DSP, DSC
• Mcu Supported Families: PIC18
• Supported Devices: Stand-alone Or W/ HPC(DM183022) Or PIC18(DM183032)
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC18
• Silicon Core Number: PIC18F
• Silicon Family Name: PIC18FxxJxx
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: HPC Explorer Board (DM183022) or PIC18 Explorer Board (DM183032)
• For Use With: DM183032 - BOARD EXPLORER PICDEM PIC18DM183022 - BOARD DEMO PIC18FXX22 64/80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F46J11 FAMILY
10.1
The PMP module has a total of 14 Special Function
Registers (SFRs) for its operation, plus one additional
register to set configuration options. Of these, eight
registers are used for control and six are used for PMP
data transfer.
10.1.1
The eight PMP Control registers are:
• PMCONH and PMCONL
• PMMODEH and PMMODEL
• PMSTATL and PMSTATH
• PMEH and PMEL
REGISTER 10-1:
DS39932C-page 166
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4-3
bit 2
bit 1
bit 0
Note 1:
PMPEN
R/W-0
Module Registers
This register is only available in 44-pin devices.
CONTROL REGISTERS
PMPEN: Parallel Master Port Enable bit
1 = PMP enabled
0 = PMP disabled, no off-chip access performed
Unimplemented: Read as ‘0’
PSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
ADRMUX<1:0>: Address/Data Multiplexing Selection bits
11 = Reserved
10 = All 16 bits of address are multiplexed on PMD<7:0> pins
01 = Lower 8 bits of address are multiplexed on PMD<7:0> pins (only eight bits of address are
00 = Address and data appear on separate pins (only eight bits of address are available in this mode)
PTBEEN: Byte Enable Port Enable bit (16-Bit Master mode)
1 = PMBE port enabled
0 = PMBE port disabled
PTWREN: Write Enable Strobe Port Enable bit
1 = PMWR/PMENB port enabled
0 = PMWR/PMENB port disabled
PTRDEN: Read/Write Strobe Port Enable bit
1 = PMRD/PMWR port enabled
0 = PMRD/PMWR port disabled
U-0
—
available in this mode)
PMCONH: PARALLEL PORT CONTROL REGISTER HIGH BYTE (BANKED F5Fh)
W = Writable bit
‘1’ = Bit is set
PSIDL
R/W-0
ADRMUX1
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
ADRMUX0
R/W-0
The
Register 10-2) control basic module operations, includ-
ing turning the module on or off. They also configure
address multiplexing and control strobe configuration.
The
Register 10-4) configure the various Master and Slave
modes, the data width and interrupt generation.
The PMEH and PMEL registers (Register 10-5 and
Register 10-6) configure the module’s operation at the
hardware (I/O pin) level.
The
Register 10-6) provide status flags for the module’s
input and output buffers, depending on the operating
mode.
PMMODE
PMCON
PMSTAT
PTBEEN
R/W-0
registers
registers
registers
© 2009 Microchip Technology Inc.
x = Bit is unknown
PTWREN
R/W-0
(Register 10-1
(Register 10-5
(Register 10-3
PTRDEN
R/W-0
bit 0
and
and
and
(1)