IXB28504XGBEFS Intel, IXB28504XGBEFS Datasheet - Page 51

• Manufacturer Part Number: IXB28504XGBEFS
• Manufacturer: Intel

Specifications of IXB28504XGBEFS

• Lead Free Status / Rohs Status: Compliant

Hardware Management—IXB2850
Table 16.
January 2007
Document Number: 05-2443-006
NPU boot parameters definition
Offset
(bytes)
2
3
7
8
12
16
16
21
25
26
30
Length
(bytes)
1
4
1
4
4
1
4
4
1
4
m
Definition
Ethernet loading flags:
Debug Ethernet IP address – A static IP address used for run-time image loading
over the debug Ethernet interface (valid only for static IP debug Ethernet
configuration)
Debug Ethernet subnet mask – A number of set bits in the subnet mask used for
run-time image loading over debug Ethernet interface (valid only for static IP debug
Ethernet configuration)
Debug Ethernet default gateway – A default gateway IP address used for run-time
image loading over the debug Ethernet interface (valid only for static IP debug
Ethernet configuration)
Base Interface #1 IP address – A static IP address used for run-time image
loading over base interface #1 (valid only for static IP base interface #1
configuration)
Base Interface #1 subnet mask – A number of set bits in the subnet mask used for
run-time image loading over base interface #1 (valid only for static IP base interface
#1 configuration)
Base Interface #1 default gateway – The default gateway IP address used for
run-time image loading over base interface #1 (valid only for static IP base interface
#1 configuration)
Base Interface #2 IP address – A static IP address used for run-time image
loading over base interface #2 (valid only for static IP base interface #2
configuration)
Base Interface #2 subnet mask – A number of set bits in the subnet mask used for
run-time image loading over base interface #2 (valid only for static IP base interface
#2 configuration)
Base Interface #2 default gateway – The default gateway IP address used for
run-time image loading over base interface #2 (valid only for static IP base interface
#2 configuration)
Image Loading Parameters Set list. A variable-length list of variable-length Image
Loading Parameters Sets (see
Loading Parameter Set describes parameters necessary to download and run one run-
time image.
• 7:7 – Ethernet tracing; a flag indicating whether traffic that comes over
• 6:6 – Debug Ethernet IP configuration type; a flag indicating type of IP
• 5:5 – Base Interface #1 IP configuration type; a flag indicating the type of IP
• 4:4 – Base Interface #2 IP configuration type; a flag indicating the type of IP
• 3:0 – BOOTP request number; a number of BOOTP requests that are sent by
Ethernet interfaces should be traced on the Boot Monitor console
- 0b Traffic is traced
- 1b Traffic is not traced
configuration used for debug Ethernet interface during run-time image loading.
This flag can have one of two values:
- 0b – Automatic; IP configuration for debug Ethernet interface should be
obtained via BOOTP protocol
- 1b – Static; IP configuration stored as boot configuration parameter are used for
the debug Ethernet interface
configuration used for base interface #1 during run-time image loading. This flag
can have one of two values:
- 0b – Automatic; the IP configuration for base interface #1 should be obtained
via BOOTP protocol
- 1b – Static; the IP configuration, stored as boot configuration parameter, is used
for base interface #1
configuration used for base interface #2 during run-time image loading. This flag
can have one of two values:
- 0b – Automatic; the IP configuration for base interface #2 should be obtained
via BOOTP protocol
- 1b – Static; the IP configuration, stored as boot configuration parameter, is used
for base interface #2
the Boot Manager over Ethernet interfaces in order to obtain IP configuration for
these interfaces
Table
Intel NetStructure
17) totaling m bytes in length. Each Image
®
IXB2850 Packet Processing Boards
TPS
51