ATMEGA128RZBV-8AU Atmel, ATMEGA128RZBV-8AU Datasheet - Page 271

• Manufacturer Part Number: ATMEGA128RZBV-8AU
• Description: MCU ATMEGA1280/AT86RF230 100TQFP
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RZBV-8AU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 100-TQFP
• Wireless Frequency: 2.4 GHz
• Interface Type: JTAG, SPI
• Output Power: 3 dBm
• For Use With: ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK501 - ADAPTER KIT FOR 64PIN AVR MCUATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: ATmega128

24. AC – Analog Comparator
24.1
2549M–AVR–09/10
Analog Comparator Multiplexed Input
The Analog Comparator compares the input values on the positive pin AIN0 and negative pin
AIN1. When the voltage on the positive pin AIN0 is higher than the voltage on the negative pin
AIN1, the Analog Comparator output, ACO, is set. The comparator’s output can be set to trigger
the Timer/Counter1 Input Capture function. In addition, the comparator can trigger a separate
interrupt, exclusive to the Analog Comparator. The user can select Interrupt triggering on com-
parator output rise, fall or toggle. A block diagram of the comparator and its surrounding logic is
shown in
The Power Reduction ADC bit, PRADC, in
must be disabled by writing a logical zero to be able to use the ADC input MUX.
Figure 24-1. Analog Comparator Block Diagram
Note:
It is possible to select any of the ADC15:0 pins to replace the negative input to the Analog Com-
parator. The ADC multiplexer is used to select this input, and consequently, the ADC must be
switched off to utilize this feature. If the Analog Comparator Multiplexer Enable bit (ACME in
ADCSRB) is set and the ADC is switched off (ADEN in ADCSRA is zero), MUX5 and MUX2:0 in
ADMUX select the input pin to replace the negative input to the Analog Comparator, as shown in
Table
log Comparator.
Table 24-1.
ACME
0
1
1
1
1
1
24-1. If ACME is cleared or ADEN is set, AIN1 is applied to the negative input to the Ana-
ADC MULTIPLEXER
1. See
2. Refer to
Figure
REFERENCE
ACME
ADEN
BANDGAP
OUTPUT
placement.
Analog Comparator Mulitiplexed Input
ADEN
Table
(1)
24-1.
1
0
0
0
0
x
ACBG
Figure 1-1 on page 2
24-1.
MUX5
0
0
0
0
x
x
ATmega640/1280/1281/2560/2561
MUX2:0
and
000
001
010
011
xxx
xxx
Table 12-5 on page 79
“PRR0 – Power Reduction Register 0” on page 56
(2)
Analog Comparator Negative Input
for Analog Comparator pin
ADC0
ADC1
ADC2
ADC3
AIN1
AIN1
271