MCF5272CVF66 Freescale Semiconductor, MCF5272CVF66 Datasheet - Page 452

• Manufacturer Part Number: MCF5272CVF66
• Description: IC MPU 32BIT 66MHZ 196-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF527xr

Specifications of MCF5272CVF66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART, USB
• Peripherals: DMA, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (4K x 32)
• Program Memory Type: ROM
• Ram Size: 1K x 32
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 196-MAPBGA
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 66MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 196
• Package Type: MA-BGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Not Compliant

Bus Operation
20.5
The MCF5272 supports byte, word, and longword operands and allows accesses to 8-, 16-, and 32-bit data
ports. The MCF5272 supports port sizes of the specific memory, enables internal generation of transfer
termination, and sets the number of wait states for the external slave being accessed by programming the
CSBRs, CSORs, SDCR, and SDTR. For more information on programming these registers, refer to the
SIM, chip select, and SDRAM controller chapters.
20.5.1
The MCF5272 can be configured for an external physical data bus width of 16 bits by pulling
QSPI_Dout/WSEL high, or for 32 bits by pulling QSPI_Dout/WSEL low during reset. When the external
physical address bus size is configured for 16 bits, the signals D[15:0] become general purpose I/O port C.
The MCF5272 determines the port size for each transfer from the CSBRs at the start of each bus cycle.
This allows the MCF5272 to transfer operands from 8-, 16-, or 32-bit ports. The size of the transfer is
adjusted to accommodate the port size indicated. A 32-bit port must reside on data bus bits D[31:0], a
16-bit port must reside on data bus bits D[31:16], and an 8-bit port must reside on data bus bits D[31:24].
This requirement ensures that the MCF5272 correctly transfers valid data to 8-, 16-, and 32-bit ports.
The bytes of operands are designated as shown in
operand is OP0; OP3 is the least significant byte. The two bytes of a word length operand are OP2 (most
significant) and OP3. The single byte of a byte length operand is OP3. These designations are used in the
figures and descriptions that follow.
20-4
Data Transfer Mechanism
Bus Sizing
The MCF5272 compares the address for the current bus transfer with the
address and mask bits in the CSBRs and CSORs looking for a match. The
priority is listed in
MCF5272 ColdFire
Table 20-2
Table 20-2. Chip Select Memory
®
Priority
Highest
Lowest
Address Decoding Priority
Integrated Microprocessor User’s Manual, Rev. 3
(from highest priority to lowest priority):
NOTE
Figure
Chip Select 0
Chip Select 1
Chip Select 2
Chip Select 3
Chip Select 4
Chip Select 5
Chip Select 6
Chip Select 7
20-1. The most significant byte of a longword
Chip Select
Freescale Semiconductor