M306N4FGGP#U3 Renesas Electronics America, M306N4FGGP#U3 Datasheet - Page 93

• Manufacturer Part Number: M306N4FGGP#U3
• Description: IC M16C/6N4 MCU FLASH 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGGP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Family Name: M16C
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: I2C/UART
• On-chip Adc: 26-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
Figure 8.12 State Transition to Stop Mode and Wait Mode
Figure 8.12 shows the State Transition to Stop Mode and Wait Mode. Figure 8.13 shows the State Transition
in Normal Operating Mode.
Table 8.8 shows a state transition matrix describing allowed transition and setting. The vertical line shows
current state and horizontal line show state after transition.
CM07 = 0
CM06 = 1
CM05 = 0
CM11 = 0
CM10 = 1
CM05, CM06, CM07: Bits in CM0 register
CM10, CM11:
NOTES:
1.
2.PLL operating mode can be entered from high-speed mode. Similarly, PLL operating mode can be changed back to high-speed mode.
3.Write to registers CM0 and CM1 per 16 bits with the CM21bit in the CM2 register = 0 (on-chip oscillator stops).
4.The on-chip oscillator clock divided by 8 provides the CPU clock.
5.Before entering stop mode, be sure to set the CM20 bit in the CM2 register to 0 (oscillation stop, re-oscillation detection function disabled).
Apr 14, 2006
Do not go directly from PLL operating mode to wait or stop mode.
Since the operation starts from the main clock after exiting stop mode, the time until the CPU operates can be reduced.
(3)
All oscillators stopped
Bits in CM1 register
Stop mode
Stop mode
Stop mode
Stop mode
page 69 of 376
Interrupt
CM10 = 1
CM10 = 1
CM10 = 1
CM10 = 1
Interrupt
Interrupt
Interrupt
(4)
(5)
(5)
(5)
(5)
dissipation
power
When
mode
low
on-chip oscillator dissipation mode
low power dissipation mode
speed
When
mode
On-chip oscillator mode,
low-
Medium-speed mode
(divided-by-8 mode)
Low-speed mode,
Normal mode
Medium-Speed Mode
High-speed mode,
Reset
PLL operating mode
(NOTES 1, 2)
WAIT
instruction
WAIT
instruction
WAIT
instruction
WAIT
instruction
Interrupt
Interrupt
Interrupt
Interrupt
8. Clock Generation Circuit
CPU operation stopped
Wait mode
Wait mode
Wait mode
Wait mode