M306N4FGGP#U3 Renesas Electronics America, M306N4FGGP#U3 Datasheet - Page 290

• Manufacturer Part Number: M306N4FGGP#U3
• Description: IC M16C/6N4 MCU FLASH 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGGP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Family Name: M16C
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: I2C/UART
• On-chip Adc: 26-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
Figure 21.9 Block Erase Command
21.3.5.5 Block Erase Command
The block erase command erases each block.
By writing xx20h in the first bus cycle and xxD0h to the highest-order even address of a block in the
second bus cycle, an auto-erase operation (erase and verify) will start in the specified block.
The FMR00 bit in the FMR0 register indicates whether an auto-erase operation has been completed.
The FMR00 bit is set to 0 (busy) during auto-erasure and to 1 (ready) when the auto-erase operation is
completed.
After the completion of an auto-erase operation, the FMR07 bit in the FMR0 register indicates whether
or not the auto-erase operation has been completed as expected. (Refer to 21.3.8 Full Status Check.)
Figure 21.9 shows a flow chart of the Block Erase Command.
The lock bit protects each block from being programmed inadvertently. (Refer to 21.3.6 Data Protect
Function.)
In EW1 mode, do not execute this command on the block where the rewrite control program is allocated.
In EW0 mode, the MCU enters read status register mode as soon as an auto-erase operation starts. The
status register can be read. The SR7 bit in the status register is set to 0 at the same time an auto-erase
operation starts. It is set to 1 when an auto-erase operation is completed. The MCU remains in read status
register mode until the read array command or read lock bit status command is written. Also execute the
clear status register command and block erase command at least 3 times until an erase error is not
generated when an erase error is generated.
Apr 14, 2006
NOTES:
1.Write the command code and data to even addresses.
2.Refer to Figure 21.12 Full Status Check and Handling Procedure for Each Error.
3.Execute the clear status register command and block erase command at least 3 times
page 266 of 376
until an erase error is not generated when an erase error is generated.
Write xxD0h to the highest-order
block address
Write the command code xx20h
Block erase operation is
completed
Full status check
FMR00=1?
Start
YES
NO
(2) (3)
21. Flash Memory Version