M306N4FGGP#U3 Renesas Electronics America, M306N4FGGP#U3 Datasheet - Page 119

• Manufacturer Part Number: M306N4FGGP#U3
• Description: IC M16C/6N4 MCU FLASH 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGGP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Family Name: M16C
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: I2C/UART
• On-chip Adc: 26-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
12. DMAC
The DMAC (Direct Memory Access Controller) allows data to be transferred without the CPU intervention.
Two DMAC channels are included. Each time a DMA request occurs, the DMAC transfers one (8- or 16-bit)
data from the source address to the destination address. The DMAC uses the same data bus as used by the
CPU. Because the DMAC has higher priority of bus control than the CPU and because it makes use of a
cycle steal method, it can transfer one word (16 bits) or one byte (8 bits) of data within a very short time after
a DMA request is generated. Figure 12.1 shows the DMAC Block Diagram. Table 12.1 lists the DMAC
Specifications. Figures 12.2 to 12.4 show the DMAC related-registers.
Figure 12.1 DMAC Block Diagram
A DMA request is generated by a write to the DSR bit in the DMiSL register (i = 0, 1), as well as by an
interrupt request which is generated by any function specified by bits DMS, and DSEL3 to DSEL0 in the
DMiSL register. However, unlike in the case of interrupt requests, DMA requests are not affected by the I flag
and the interrupt control register, so that even when interrupt requests are disabled and no interrupt request
can be accepted, DMA requests are always accepted. Furthermore, because the DMAC does not affect
interrupts, the IR bit in the interrupt control register does not change state due to a DMA transfer.
A data transfer is initiated each time a DMA request is generated when the DMAE bit in the DMiCON register
= 1 (DMA enabled). However, if the cycle in which a DMA request is generated is faster than the DMA
transfer cycle, the number of transfer requests generated and the number of times data is transferred may
not match. For details, refer to 12.4 DMA Request.
NOTE:
1.Pointer is incremented by a DMA request.
Apr 14, 2006
DMA0 transfer counter TCR0
DMA0 transfer counter reload register TCR0
DMA1 transfer counter reload register TCR1
DMA1 transfer counter TCR1
page 95 of 376
Data bus high-order bits
Data bus low-order bits
Address bus
DMA0 source pointer SAR0
DMA0 destination pointer DAR0
DMA0 forward address pointer
DMA1 source pointer SAR1
DMA1 destination pointer DAR1
DMA1 forward address pointer
DMA latch high-order bits
DMA latch low-order bits
(1)
(1)
12. DMAC