M306N4FGGP#U3 Renesas Electronics America, M306N4FGGP#U3 Datasheet - Page 258

• Manufacturer Part Number: M306N4FGGP#U3
• Description: IC M16C/6N4 MCU FLASH 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGGP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Family Name: M16C
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: I2C/UART
• On-chip Adc: 26-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
19.15 Reception and Transmission
Table 19.3 CAN Reception and Transmission Mode Configuration
TrmReq, RecReq, Remote, RspLock, RemActive, RspLock: Bits in CiMCTLj register (i = 0, 1, j = 0 to 15)
TrmReq RecReq Remote RspLock
Table 19.3 lists the CAN Reception and Transmission Mode Configuration.
When configuring a slot as a reception slot, note the following points.
(1) Before configuring a slot as a reception slot, be sure to set the CiMCTLj register to 00h.
(2) A received message is stored in a slot that matches the condition first according to the result of reception
(3) In normal CAN operation mode, when a CAN module transmits a message of which ID matches, the
When configuring a slot as a transmission slot, note the following points.
(1) Before configuring a slot as a transmission slot, be sure to set the CiMCTLj registers to 00h.
(2) Set the TrmReq bit in the CiMCTLj register to 0 (not transmission slot) before rewriting a transmission slot.
(3) A transmission slot should not be rewritten when the TrmActive bit in the CiMCTLj register is 1
0
0
1
1
0
mode configuration and acceptance filtering operation. Upon deciding in which slot to store, the smaller
the number of the slot is, the higher priority it has.
CAN module never receives the transmitted data. In loop back mode, however, the CAN module
receives back the transmitted data. In this case, the module does not return ACK.
(transmitting).
If it is rewritten, an undefined data will be transmitted.
Apr 14, 2006
0
1
0
0
1
page 234 of 376
0
1
0
1
-
1/0
0
0
0
-
Communication environment configuration mode:
configure the communication mode of the slot.
Configured as a reception slot for a data frame.
Configured as a transmission slot for a remote frame.
(At this time the RemActive = 1.)
After completion of transmission, this functions as a reception
slot for a data frame. (At this time the RemActive = 0.)
However, when an ID that matches on the CAN bus is detected
before remote frame transmission, this immediately functions
as a reception slot for a data frame.
Configured as a transmission slot for a data frame.
Configured as a reception slot for a remote frame.
(At this time the RemActive = 1.)
After completion of reception, this functions as a transmission
slot for a data frame. (At this time the RemActive = 0.)
However, transmission does not start as long as RspLock bit
remains 1; thus no automatic response.
Response (transmission) starts when the RspLock bit is set to 0.
Communication Mode of Slot
19. CAN Module