M306N4FGGP#U3 Renesas Electronics America, M306N4FGGP#U3 Datasheet - Page 216

• Manufacturer Part Number: M306N4FGGP#U3
• Description: IC M16C/6N4 MCU FLASH 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGGP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Family Name: M16C
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: I2C/UART
• On-chip Adc: 26-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
Figure 15.40 SOUT3’s Initial Value Setting
15.2.3 Functions for Setting SOUT3 Initial Value
If the SM36 bit in the S3C register is set to 0 (external clock), the SOUT3 pin output can be fixed high or
low when not transferring. However, the last bit value of the former data is retained between data and
data when transmitting the continuous data.
Figure 15.40 shows the timing chart and how to set it for the SOUT3’s Initial Value Setting.
(Example) When "H" selected for SOUT3 initial value
* This diagram applies to the case where the bits in the S3C register are set as follows:
NOTES:
SOUT3 (internal)
Signal written to
S3TRR register
1.If the SM36 bit = 1 (internal clock) or if the SM32 bit = 1 (SOUT3 output disabled), this output
2.SOUT3 can only be initialized when input on the CLK3 pin is in the high state if the SM34 bit in
SOUT3 output
Apr 14, 2006
goes to the high-impedance state.
the S3C register = 0 (transmit data output at the falling edge of the transfer clock) or in the low
state if the SM34 bit = 1 (transmit data output at the rising edge of the transfer clock).
SM32 = 0 (SOUTi output)
SM35 = 0 (LSB first)
SM36 = 0 (external clock)
SM37 bit
SM33 bit
Setting the SOUT3
initial value to "H"
Port output
page 192 of 376
(2)
Port selection switching
(I/O port
Initial value = H
SOUT3)
(1)
D0
D0
(SOUT3 pin functions as SOUT3 output)
(SOUT3 pin functions as an I/O port)
Setting of the initial value of SOUT3
Serial transmit/reception starts
Write to the S3TRR register
(SOUT3 initial value = H)
transmission/reception
output and starting of
Set the SM33 bit to 0
Set the SM37 bit to 1
Set the SM33 bit to 1
"H" level is output
from the SOUT3 pin
15. Serial Interface