MC9S12NE64VTU Freescale Semiconductor, MC9S12NE64VTU Datasheet - Page 484

• Manufacturer Part Number: MC9S12NE64VTU
• Description: IC MCU 25MHZ ETHERNET/PHY 80TQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12NE64VTU

• Mfg Application Notes: MC9S12NE64 Integrated Ethernet Controller Implementing an Ethernet Interface with the MC9S12NE64 Web Server Development with MC9S12NE64 and Open TCP
• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 3.465 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 80-TQFP Exposed Pad, 80-eTQFP, 80-HTQFP, 80-VQFP
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 16 bit
• Operating Supply Voltage: - 0.3 V to + 3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 65 C
• On-chip Adc: 10 bit
• For Use With: EVB9S12NE64E - BOARD EVAL FOR 9S12NE64DEMO9S12NE64E - DEMO BOARD FOR 9S12NE64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 18 Debug Module (DBGV1)
18.3.2.8
1
2
484
BKAMB[H:L]
In DBG mode, BKAMBH:BKAMBL has no meaning and are forced to 0’s.
In DBG mode, BKBMBH:BKBMBL are used in full mode to qualify data.
RWCEN
Reset
Field
RWC
Field
7:6
1
0
W
R
BKAMBH
Read/Write Comparator C Enable Bit — The RWCEN bit controls whether read or write comparison is enabled
for comparator C. RWCEN is not useful for tagged breakpoints.
0 Read/Write is not used in comparison
1 Read/Write is used in comparison
Read/Write Comparator C Value Bit — The RWC bit controls whether read or write is used in compare for
comparator C. The RWC bit is not used if RWCEN = 0.
0 Write cycle will be matched
1 Read cycle will be matched
Breakpoint Mask High Byte for First Address — In dual or full mode, these bits may be used to mask (disable)
the comparison of the high and/or low bytes of the first address breakpoint. The functionality is as given in
Table
The x:0 case is for a full address compare. When a program page is selected, the full address compare will be
based on bits for a 20-bit compare. The registers used for the compare are {DBGCAX[5:0], DBGCAH[5:0],
DBGCAL[7:0]}, where DBGAX[5:0] corresponds to PPAGE[5:0] or extended address bits [19:14] and CPU
address [13:0]. When a program page is not selected, the full address compare will be based on bits for a 16-bit
compare. The registers used for the compare are {DBGCAH[7:0], DBGCAL[7:0]} which corresponds to CPU
address [15:0].
Note: This extended address compare scheme causes an aliasing problem in BKP mode in which several
The 1:0 case is not sensible because it would ignore the high order address and compare the low order and
expansion addresses. Logic forces this case to compare all address lines (effectively ignoring the BKAMBH
control bit).
The 1:1 case is useful for triggering a breakpoint on any access to a particular expansion page. This only makes
sense if a program page is being accessed so that the breakpoint trigger will occur only if DBGCAX compares.
Debug Control Register 3 (DBGC3)
0
7
18-16.
physical addresses may match with a single logical address. This problem may be avoided by using DBG
mode to generate breakpoints.
1
BKAMBL
0
6
Table 18-14. DBGC2 Field Descriptions (continued)
Figure 18-14. Debug Control Register 3 (DBGC3)
1
Table 18-15. DBGC3 Field Descriptions
BKBMBH
MC9S12NE64 Data Sheet, Rev. 1.1
0
5
2
BKBMBL
0
4
Description
Description
2
RWAEN
0
3
RWA
0
2
RWBEN
Freescale Semiconductor
0
1
RWB
0
0