MC9S12NE64VTU Freescale Semiconductor, MC9S12NE64VTU Datasheet - Page 275

• Manufacturer Part Number: MC9S12NE64VTU
• Description: IC MCU 25MHZ ETHERNET/PHY 80TQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12NE64VTU

• Mfg Application Notes: MC9S12NE64 Integrated Ethernet Controller Implementing an Ethernet Interface with the MC9S12NE64 Web Server Development with MC9S12NE64 and Open TCP
• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 3.465 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 80-TQFP Exposed Pad, 80-eTQFP, 80-HTQFP, 80-VQFP
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 16 bit
• Operating Supply Voltage: - 0.3 V to + 3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 65 C
• On-chip Adc: 10 bit
• For Use With: EVB9S12NE64E - BOARD EVAL FOR 9S12NE64DEMO9S12NE64E - DEMO BOARD FOR 9S12NE64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Data reception is double buffered. Data is shifted serially into the SPI shift register during the transfer and
is transferred to the parallel SPI Data Register after the last bit is shifted in.
After the 16th (last) SCK edge:
Figure 9-9
CPOL = 0 and CPOL = 1. The diagram may be interpreted as a master or slave timing diagram because
the SCK, MISO, and MOSI pins are connected directly between the master and the slave. The MISO signal
is the output from the slave and the MOSI signal is the output from the master. The SS pin of the master
must be either high or reconfigured as a general-purpose output not affecting the SPI.
In slave mode, if the SS line is not deasserted between the successive transmissions then the content of the
SPI Data Register is not transmitted, instead the last received byte is transmitted. If the SS line is deasserted
for at least minimum idle time (half SCK cycle) between successive transmissions then the content of the
SPI Data Register is transmitted.
Freescale Semiconductor
•
•
End of Idle State
SCK Edge Nr.
MSB first (LSBFE = 0):
SCK (CPOL = 0)
SCK (CPOL = 1)
SAMPLE I
MOSI/MISO
CHANGE O
CHANGE O
SEL SS (O)
Master only
SEL SS (I)
t
t
t
t
MOSI pin
MISO pin
Data that was previously in the master SPI Data Register should now be in the slave data register
and the data that was in the slave data register should be in the master.
The SPIF flag in the SPI Status Register is set indicating that the transfer is complete.
LSB first (LSBFE = 1):
L
T
I
L
, t
= Minimum idling time between transfers (minimum SS high time)
= Minimum leading time before the first SCK edge
= Minimum trailing time after the last SCK edge
T
, and t
is a timing diagram of an SPI transfer where CPHA = 0. SCK waveforms are shown for
I
are guaranteed for the master mode and required for the slave mode.
tL
MSB
LSB
1
2
Figure 9-9. SPI Clock Format 0 (CPHA = 0)
Begin
Bit 6
Bit 1
3
MC9S12NE64 Data Sheet, Rev. 1.1
4
Bit 5
Bit 2
5
6
Bit 4
Bit 3
7
Transfer
8
Bit 3
Bit 4
9
10
Bit 2
Bit 5
11
12
Bit 1
Bit 6
13 14
End
MSB
15
LSB
16
Minimum 1/2 SCK
tT
for t
Begin of Idle State
Functional Description
T
tI
, t
l
, t
L
tL
275