MC9S12NE64VTU Freescale Semiconductor, MC9S12NE64VTU Datasheet - Page 278

• Manufacturer Part Number: MC9S12NE64VTU
• Description: IC MCU 25MHZ ETHERNET/PHY 80TQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12NE64VTU

• Mfg Application Notes: MC9S12NE64 Integrated Ethernet Controller Implementing an Ethernet Interface with the MC9S12NE64 Web Server Development with MC9S12NE64 and Open TCP
• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 3.465 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 80-TQFP Exposed Pad, 80-eTQFP, 80-HTQFP, 80-VQFP
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 16 bit
• Operating Supply Voltage: - 0.3 V to + 3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 65 C
• On-chip Adc: 10 bit
• For Use With: EVB9S12NE64E - BOARD EVAL FOR 9S12NE64DEMO9S12NE64E - DEMO BOARD FOR 9S12NE64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 9 Serial Peripheral Interface (SPIV3)
The baud rate generator is activated only when the SPI is in the master mode and a serial transfer is taking
place. In the other cases, the divider is disabled to decrease I
9.4.5
9.4.5.1
The SS output feature automatically drives the SS pin low during transmission to select external devices
and drives it high during idle to deselect external devices. When SS output is selected, the SS output pin
is connected to the SS input pin of the external device.
The SS output is available only in master mode during normal SPI operation by asserting SSOE and
MODFEN bit as shown in
The mode fault feature is disabled while SS output is enabled.
9.4.5.2
The bidirectional mode is selected when the SPC0 bit is set in SPI Control Register 2 (see
this mode, the SPI uses only one serial data pin for the interface with external device(s). The MSTR bit
decides which pin to use. The MOSI pin becomes the serial data I/O (MOMI) pin for the master mode, and
the MISO pin becomes serial data I/O (SISO) pin for the slave mode. The MISO pin in master mode and
MOSI pin in slave mode are not used by the SPI.
278
Bidirectional Mode
When SPE = 1
Normal Mode
SPC0 = 0
SPC0 = 1
Special Features
SS Output
Bidirectional Mode (MOSI or MISO)
Care must be taken when using the SS output feature in a multimaster
system because the mode fault feature is not available for detecting system
errors between masters.
Serial Out
Serial Out
Table
Serial In
Serial In
SPI
SPI
Table 9-9. Normal Mode and Bidirectional Mode
BaudRateDivisor
Master Mode MSTR = 1
Figure 9-11. Baud Rate Divisor Equation
9-3.
BIDIROE
MC9S12NE64 Data Sheet, Rev. 1.1
=
NOTE
(
SPPR
MOMI
MOSI
MISO
+
1
DD
) 2
•
current.
(
SPR
Serial Out
Serial Out
+
Serial In
Serial In
SPI
SPI
1
)
Slave Mode MSTR = 0
BIDIROE
Freescale Semiconductor
Table
MOSI
MISO
SISO
9-9). In