AT90PWM81 Atmel Corporation, AT90PWM81 Datasheet - Page 47

• Manufacturer Part Number: AT90PWM81
• Manufacturer: Atmel Corporation

Specifications of AT90PWM81

• Flash (kbytes): 8 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 20
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 8
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

6.7.7
6.8
6.8.1
6.8.2
7734P–AVR–08/10
Register description
On-chip Debug System
Sleep Mode Control Register – SMCR
Power Reduction Register - PRR
For analog input pins, the digital input buffer should be disabled at all times. An analog signal level close
to V
disabled by writing to the Digital Input Disable Registers (DIDR1 and DIDR0). Refer to “Digital Input
Disable Register 1– DIDR1” and “Digital Input Disable Register 0 – DIDR0” on
for details.
If the On-chip debug system is enabled by OCDEN Fuse and the chip enter sleep mode, the main clock
source is enabled, and hence, always consumes power. In the deeper sleep modes, this will contribute sig-
nificantly to the total current consumption.
The Sleep Mode Control Register contains control bits for power management.
• Bits 3..1 – SM2..0: Sleep Mode Select Bits 2, 1, and 0
These bits select between the five available sleep modes as shown in
Table 6-2.
Note:
• Bit 1 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP instruc-
tion is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s purpose, it is
recommended to write the Sleep Enable (SE) bit to one just before the execution of the SLEEP instruction
and to clear it immediately after waking up.
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
CC
SM2
/2 on an input pin can cause significant current even in active mode. Digital input buffers can be
0
0
0
0
1
1
1
1
1. Standby mode is only recommended for use with external crystals or resonators.
7
PRPSC2
R/W
0
7
–
R
0
Sleep Mode Select
SM1
-
6
R
0
0
0
1
1
0
0
1
1
6
–
R
0
5
PRPSCR
R/W
0
5
–
R
0
SM0
0
1
0
1
0
1
0
1
4
PRTIM1
R/W
0
4
–
R
0
Sleep Mode
Idle
ADC Noise Reduction
Power-down
Reserved
Reserved
Reserved
Standby
Reserved
3
-
R
0
3
SM2
R/W
0
(1)
2
PRSPI
R/W
0
2
SM1
R/W
0
Table
1
SM0
R/W
0
1
-
R
0
6-2.
AT90PWM81
page 202
0
SE
R/W
0
0
PRADC
R/W
0
and
SMCR
page 221
PRR
47