PIC18F67K22-I/MR Microchip Technology, PIC18F67K22-I/MR Datasheet - Page 359

• Manufacturer Part Number: PIC18F67K22-I/MR
• Description: 128kB Flash, 4kB RAM, 1kB EE, NanoWatt XLP, GP 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F67K22-I/MR

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

REGISTER 23-10: ANCON2: A/D PORT CONFIGURATION REGISTER 2
The analog reference voltage is software-selectable to
either the device’s positive and negative supply voltage
(AV
RA3/AN3/V
two additional Internal Reference Voltage selections:
2.048V and 4.096V.
The A/D Converter can uniquely operate while the
device is in Sleep mode. To operate in Sleep, the A/D
conversion clock must be derived from the A/D
Converter’s internal RC oscillator.
The output of the Sample-and-Hold (S/H) is the input
into the converter, which generates the result via
successive approximation.
 2009-2011 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-0
Note 1:
ANSEL23
DD
R/W-1
and AV
(1)
REF
AN15 through AN12 and AN23 through AN20 are implemented only on 80-pin devices. For 64-pin
devices, the corresponding ANSELx bits are still implemented for these channels, but have no effect.
+ and RA2/AN2/V
ANSEL<23:16>: Analog Port Configuration bits (AN23 through AN16)
1 = Pin is configured as an analog channel; digital input is disabled and any inputs read as ‘ 0 ’
0 = Pin is configured as a digital port
ANSEL22
SS
R/W-1
) or the voltage level on the
(1)
W = Writable bit
‘1’ = Bit is set
ANSEL21
REF
R/W-1
- pins. V
(1)
REF
ANSEL20
R/W-1
+ has
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
PIC18F87K22 FAMILY
ANSEL19
R/W-1
Each port pin associated with the A/D Converter can be
configured as an analog input or a digital I/O. The
ADRESH and ADRESL registers contain the result of
the A/D conversion. When the A/D conversion is com-
plete, the result is loaded into the ADRESH:ADRESL
register pair, the GO/DONE bit (ADCON0<1>) is
cleared and the A/D Interrupt Flag bit, ADIF (PIR1<6>),
is set.
A device Reset forces all registers to their Reset state.
This forces the A/D module to be turned off and any
conversion in progress is aborted. The value in the
ADRESH:ADRESL register pair is not modified for a
Power-on Reset. These registers will contain unknown
data after a Power-on Reset.
The block diagram of the A/D module is shown in
Figure
23-4.
ANSEL18
R/W-1
(1)
x = Bit is unknown
ANSEL17
R/W-1
DS39960D-page 359
ANSEL16
R/W-1
bit 0