AT91CAP7E-NA-ZJ Atmel, AT91CAP7E-NA-ZJ Datasheet - Page 190

• Manufacturer Part Number: AT91CAP7E-NA-ZJ
• Description: MCU CAP7 FPGA 225LFBGA
• Manufacturer: Atmel
• Series: CAP™r

Specifications of AT91CAP7E-NA-ZJ

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 80MHz
• Connectivity: EBI/EMI, FPGA, IrDA, SPI, UART/USART, USB
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: ROM
• Ram Size: 160K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 225-LFBGA
• Processor Series: AT91Mx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

22.7.5
Register Name:
Access Type:
Reset Value:
• LPCB: Low-power Configuration Bits
• PASR: Partial Array Self-refresh (only for low-power SDRAM)
PASR parameter is transmitted to the SDRAM during initialization to specify whether only one quarter, one half or all banks
of the SDRAM array are enabled. Disabled banks are not refreshed in self-refresh mode. This parameter must be set
according to the SDRAM device specification.
• TCSR: Temperature Compensated Self-Refresh (only for low-power SDRAM)
TCSR parameter is transmitted to the SDRAM during initialization to set the refresh interval during self-refresh mode
depending on the temperature of the low-power SDRAM. This parameter must be set according to the SDRAM device
specification.
• DS: Drive Strength (only for low-power SDRAM)
DS parameter is transmitted to the SDRAM during initialization to select the SDRAM strength of data output. This parame-
ter must be set according to the SDRAM device specification.
190
00
01
10
11
31
23
15
–
–
–
7
–
AT91CAP7E
SDRAMC Low Power Register
Low Power Feature is inhibited: no Power-down, Self-refresh or Deep Power-down command is issued
to the SDRAM device.
The SDRAM Controller issues a Self-refresh command to the SDRAM device, the SDCLK clock is
deactivated and the SDCKE signal is set low. The SDRAM device leaves the Self Refresh Mode when
accessed and enters it after the access.
The SDRAM Controller issues a Power-down Command to the SDRAM device after each access, the
SDCKE signal is set to low. The SDRAM device leaves the Power-down Mode when accessed and
enters it after the access.
The SDRAM Controller issues a Deep Power-down command to the SDRAM device. This mode is
unique to low-power SDRAM.
30
22
14
–
–
–
6
PASR
29
21
13
–
–
5
TIMEOUT
SDRAMC_LPR
Read/Write
0x0
28
20
12
–
–
4
27
19
11
–
–
3
–
DS
26
18
10
–
–
2
–
25
17
–
–
9
1
TCSR
LPCB
8549A–CAP–10/08
24
16
–
–
8
0