LPC1343FHN33,551 NXP Semiconductors, LPC1343FHN33,551 Datasheet - Page 302

• Manufacturer Part Number: LPC1343FHN33,551
• Description: IC MCU 32BIT 32KB FLASH 33HVQFN
• Manufacturer: NXP Semiconductors
• Series: LPC13xxr

Specifications of LPC1343FHN33,551

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 33-VQFN Exposed Pad, 33-HVQFN, 33-SQFN, 33-DHVQFN
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 28
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC13
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, UART
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 28
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, KSK-LPC1343
• Development Tools By Supplier: OM11039, OM11040, OM11046, OM11048
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 33HVQFN EP
• Device Core: ARM Cortex M3
• Family Name: LPC1000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4944; 935289655551

NXP Semiconductors
UM10375
User manual
19.13.8 Go <address> <mode>
19.13.9 Erase sector(s) <start sector number> <end sector number>
Table 299. ISP Go command
Table 300. ISP Erase sector command
Command
Input
Return Code CMD_SUCCESS |
Description
Example
Command
Input
Return Code CMD_SUCCESS |
Description
Example
G
Address: Flash or RAM address from which the code execution is to be started.
This address should be on a word boundary.
Mode: T (Execute program in Thumb Mode) | A (Execute program in ARM mode).
ADDR_ERROR |
ADDR_NOT_MAPPED |
CMD_LOCKED |
PARAM_ERROR |
CODE_READ_PROTECTION_ENABLED
This command is used to execute a program residing in RAM or flash memory. It
may not be possible to return to the ISP command handler once this command is
successfully executed. This command is blocked when code read protection is
enabled.
"G 0 A<CR><LF>" branches to address 0x0000 0000 in ARM mode.
E
Start Sector Number
End Sector Number: Should be greater than or equal to start sector number.
BUSY |
INVALID_SECTOR |
SECTOR_NOT_PREPARED_FOR_WRITE_OPERATION |
CMD_LOCKED |
PARAM_ERROR |
CODE_READ_PROTECTION_ENABLED
This command is used to erase one or more sector(s) of on-chip flash memory. The
boot block can not be erased using this command. This command only allows
erasure of all user sectors when the code read protection is enabled.
"E 2 3<CR><LF>" erases the flash sectors 2 and 3.
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 7 July 2010
Chapter 19: LPC13xx Flash memory programming firmware
UM10375
© NXP B.V. 2010. All rights reserved.
304 of 333