LPC1343FHN33,551 NXP Semiconductors, LPC1343FHN33,551 Datasheet - Page 133

• Manufacturer Part Number: LPC1343FHN33,551
• Description: IC MCU 32BIT 32KB FLASH 33HVQFN
• Manufacturer: NXP Semiconductors
• Series: LPC13xxr

Specifications of LPC1343FHN33,551

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 33-VQFN Exposed Pad, 33-HVQFN, 33-SQFN, 33-DHVQFN
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 28
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC13
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, UART
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 28
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, KSK-LPC1343
• Development Tools By Supplier: OM11039, OM11040, OM11046, OM11048
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 33HVQFN EP
• Device Core: ARM Cortex M3
• Family Name: LPC1000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4944; 935289655551

NXP Semiconductors
UM10375
User manual
9.10.1.4 USB Device Interrupt Set register (USBDevIntSet - 0x4002 000C)
9.10.2.1 USB Command Code register (USBCmdCode - 0x4001 8010)
9.10.2 SIE command code registers
Table 158. USB Device Interrupt Clear register (USBDevIntClr - address 0x4002 0008) bit
Writing one to a bit in this register sets the corresponding bit in the USBDevIntSt. Writing a
zero has no effect
USBDevIntSet is a write only register.
Table 159. USB Device Interrupt Set register (USBDevIntSet - address 0x4002 000C) bit
The SIE command code registers are used for communicating with the Serial Interface
Engine. See
information.
This register is used for sending the command and write data to the SIE. The commands
written here are propagated to the SIE and executed there. After executing the command,
the register is empty, and the CCEMPTY bit of USBDevIntSt register is set. See
Section 9.11
Table 160. USB Command Code register (USBCmdCode - address 0x4002 0010) bit
Bit
31:0
Bit
31:0
Bit
7:0
15:8
Symbol
See
Symbol
See
Symbol
-
CMD_PHASE
description
description
description
Table 155
Table 155
Section 9.11 “Serial interface engine command description”
for details. USBCmdCode is a write only register.
All information provided in this document is subject to legal disclaimers.
Value
0
1
Value
-
Value
0
1
Rev. 2 — 7 July 2010
Description
No effect.
The corresponding bit in USBDevIntSt
cleared.
Description
No effect.
The corresponding bit in USBDevIntSt
set.
Description
Reserved, user software should not write ones to
reserved bits. The value read from a reserved bit is
not defined.
The command phase:
Chapter 9: LPC13xx USB device controller
(Table
(Table
UM10375
© NXP B.V. 2010. All rights reserved.
156) is
156) is
for more
Reset
value
NA
0x00
Reset
value
0
135 of 333
Reset
value
0