LPC1343FHN33,551 NXP Semiconductors, LPC1343FHN33,551 Datasheet - Page 268

• Manufacturer Part Number: LPC1343FHN33,551
• Description: IC MCU 32BIT 32KB FLASH 33HVQFN
• Manufacturer: NXP Semiconductors
• Series: LPC13xxr

Specifications of LPC1343FHN33,551

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 33-VQFN Exposed Pad, 33-HVQFN, 33-SQFN, 33-DHVQFN
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 28
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC13
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, UART
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 28
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, KSK-LPC1343
• Development Tools By Supplier: OM11039, OM11040, OM11046, OM11048
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 33HVQFN EP
• Device Core: ARM Cortex M3
• Family Name: LPC1000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4944; 935289655551

NXP Semiconductors
UM10375
User manual
15.8.12 PWM Control Register (TMR32B0PWMC and TMR32B1PWMC)
When Counter Mode is chosen as a mode of operation, the CAP input (selected by the
CTCR bits 3:2) is sampled on every rising edge of the PCLK clock. After comparing two
consecutive samples of this CAP input, one of the following four events is recognized:
rising edge, falling edge, either of edges or no changes in the level of the selected CAP
input. Only if the identified event occurs, and the event corresponds to the one selected by
bits 1:0 in the CTCR register, will the Timer Counter register be incremented.
Effective processing of the externally supplied clock to the counter has some limitations.
Since two successive rising edges of the PCLK clock are used to identify only one edge
on the CAP selected input, the frequency of the CAP input can not exceed one half of the
PCLK clock. Consequently, duration of the HIGH/LOW levels on the same CAP input in
this case can not be shorter than 1/(2 × PCLK).
Table 264: Count Control Register (TMR32B0CTCR - address 0x4001 4070 and TMR32B1TCR
The PWM Control Register is used to configure the match outputs as PWM outputs. Each
match output can be independently set to perform either as PWM output or as match
output whose function is controlled by the External Match Register (EMR).
For each timer, a maximum of three-single edge controlled PWM outputs can be selected
on the MATn[2:0] outputs. One additional match register determines the PWM cycle
length. When a match occurs in any of the other match registers, the PWM output is set to
Bit
1:0
3:2
31:4
Symbol
Counter/
Timer
Mode
Count
Input
Select
-
- address 0x4001 8070) bit description
All information provided in this document is subject to legal disclaimers.
Value
00
01
10
11
00
01
10
11
-
Rev. 2 — 7 July 2010
Description
This field selects which rising PCLK edges can increment
Timer’s Prescale Counter (PC), or clear PC and increment
Timer Counter (TC).
Timer Mode: every rising PCLK edge
Counter Mode: TC is incremented on rising edges on the
CAP input selected by bits 3:2.
Counter Mode: TC is incremented on falling edges on the
CAP input selected by bits 3:2.
Counter Mode: TC is incremented on both edges on the CAP
input selected by bits 3:2.
When bits 1:0 in this register are not 00, these bits select
which CAP pin is sampled for clocking:
CT32Bn_
CAP0
Reserved
Reserved
Reserved
Note: If Counter mode is selected in the TnCTCR, the 3 bits
for that input in the Capture Control Register (TnCCR) must
be programmed as 000.
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
Chapter 15: LPC13xx 32-bit timer/counters (CT32B0/1)
UM10375
© NXP B.V. 2010. All rights reserved.
270 of 333
Reset
value
00
00
NA