C8051F131R Silicon Labs, C8051F131R Datasheet - Page 344

• Manufacturer Part Number: C8051F131R
• Description: 8-bit Microcontrollers - MCU 128kB 100MIPS 8448B RAM
• Manufacturer: Silicon Labs

Specifications of C8051F131R

• Product Category: 8-bit Microcontrollers - MCU
• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 100 MHz
• Program Memory Size: 128 KB
• Data Ram Size: 8.25 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2.7 V to 3.6 V
• Package / Case: TQFP-64
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 9
• Data Rom Size: 64 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 32
• Number Of Timers: 16 bit
• Processor Series: C8051
• Program Memory Type: Flash
• Factory Pack Quantity: 500
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 3 V

C8051F120/1/2/3/4/5/6/7
C8051F130/1/2/3
25.2. Flash Programming Commands
The Flash memory can be programmed directly over the JTAG interface using the Flash Control, Flash
Data, Flash Address, and Flash Scale registers. These Indirect Data Registers are accessed via the JTAG
Instruction Register. Read and write operations on indirect data registers are performed by first setting the
appropriate DR address in the IR register. Each read or write is then initiated by writing the appropriate
Indirect Operation Code (IndOpCode) to the selected data register. Incoming commands to this register
have the following format:
IndOpCode: These bit set the operation to perform according to the following table:
The Poll operation is used to check the Busy bit as described below. Although a Capture-DR is performed,
no Update-DR is allowed for the Poll operation. Since updates are disabled, polling can be accomplished
by shifting in/out a single bit.
The Read operation initiates a read from the register addressed by the DRAddress. Reads can be initiated
by shifting only 2 bits into the indirect register. After the read operation is initiated, polling of the Busy bit
must be performed to determine when the operation is complete.
The write operation initiates a write of WriteData to the register addressed by DRAddress. Registers of any
width up to 18 bits can be written. If the register to be written contains fewer than 18 bits, the data in Write-
Data should be left-justified, i.e. its MSB should occupy bit 17 above. This allows shorter registers to be
written in fewer JTAG clock cycles. For example, an 8-bit register could be written by shifting only 10 bits.
After a Write is initiated, the Busy bit should be polled to determine when the next operation can be initi-
ated. The contents of the Instruction Register should not be altered while either a read or write operation is
busy.
Outgoing data from the indirect Data Register has the following format:
The Busy bit indicates that the current operation is not complete. It goes high when an operation is initiated
and returns low when complete. Read and Write commands are ignored while Busy is high. In fact, if poll-
ing for Busy to be low will be followed by another read or write operation, JTAG writes of the next operation
can be made while checking for Busy to be low. They will be ignored until Busy is read low, at which time
the new operation will initiate. This bit is placed ate bit 0 to allow polling by single-bit shifts. When waiting
for a Read to complete and Busy is 0, the following 18 bits can be shifted out to obtain the resulting data.
ReadData is always right-justified. This allows registers shorter than 18 bits to be read using a reduced
number of shifts. For example, the results from a byte-read requires 9 bit shifts (Busy + 8 bits).
344
19
0
IndOpCode
19:18
IndOpCode
10
0x
11
ReadData
Rev. 1.4
18:1
Operation
Read
Write
Poll
WriteData
17:0
Busy
0